FUNAI FDR-90E - Manual (Page 7)

Functional overview
Before you start
Recor
ding
Pla
ying discs
Editing
Bef
or
e y
ou star
t
Connections
Getting star
ted
Changing the SETUP men
u
Others
Español
F
rançais
7
Front Panel
1. POWER button
Press to turn the DVD recorder on and off.
If timer programmings have been set, press to
set the unit in timer-standby mode.
2. STOP C button
Press to stop play or recording.
3. REV H button
Press to skip to the previous chapter or track.
Press and hold for
1.5 seconds to fast reverse.
4. PLAY B button
Press to start or resume play.
5. FWD G button
Press to skip to the next chapter or track.
Press and hold for
1.5 seconds to fast forward.
6. CHANNEL L / K button
Press to change the channel up and down.
7. A OPEN/CLOSE button
Press to open or close the disc tray.
8. Disc tray
Place a disc when open.
9. Display
Refer to “Guide to Displays on the front panel” on
page 12.
10. Remote control sensor
Receive signals from your remote control so that you
can control the DVD recorder from a distance.
11. REC SPEED button
Press to switch the recording speed.
12. REC button
Press once to start a recording. Press repeatedly to
start a One-Touch Recording.
13. AUDIO (L/R) input jacks (LINE2)
Use to connect external equipment with standard
audio cables.
14. VIDEO input jack (LINE2)
Use to connect external equipment with a standard
video cable.
15. S-VIDEO input jack (LINE2)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
Rear Panel
OUT
TV ANTENNA
IN
COMPONENT
VIDEO OUTPUT
P R /C R
P B /C B
Y
VIDEO
OUTPUT
INPUT
AUDIO
1
2
AUDIO
DIGITAL AUDIO OUTPUT
PCM / BITSTREAM
COAXIAL O P T I C A L
S-VIDEO
VIDEO (L1) S-VIDEO L
R L
R
1 3 6 2
10 9 7
4
8
5
11
1. AC Power Cord
Connect to a standard AC outlet to supply power to this
unit.
2. AUDIO OUTPUT jacks 1, 2
Use to connect a TV monitor, AV receiver or other
equipment with standard audio cables.
3. VIDEO OUTPUT jack
Use to connect a TV monitor, AV receiver or other
equipment with a standard video cable.
4. S-VIDEO OUTPUT jack
Use to connect the S-Video input of a TV monitor, AV
receiver or other equipment with an S-Video cable.
5. COMPONENT VIDEO OUTPUT jacks
Use to connect a TV monitor with component video
inputs with component video cables.
6. TV ANTENNA IN jack
Use to connect an antenna.
7. TV ANTENNA OUT jack
Use to connect an antenna cable to pass the signal
from the TV ANTENNA IN to your TV monitor.
8. S-VIDEO INPUT jack(LINE 1)
Use to connect the S-Video output of external equip-
ment with an S-Video cable.
9. VIDEO INPUT jack(LINE 1)
Use to connect external equipment with a standard
video cable.
10. AUDIO INPUT jacks(LINE1)
Use to connect external equipment with standard
audio cables.
11. DIGITAL AUDIO OUTPUT jacks
Use to connect an AV receiver, Dolby Digital decoder,
DTS decoder or other equipment with digital input
jacks with a digital coaxial cable or a digital optical
cable.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to
the DVD recorder.
• This unit does not have the RF modulator.
POWER
S-VIDEO VIDEO
STOP REV PLAY FWD CHANNEL OPEN/CLOSE
L - AUDIO - R
REC REC SPEED
1 2 3 4 5 6 7
11
8 9
10 12 15 13 14
E6550UD(EN_SP_FR).qx3 04.8.10 11:34 Page 7