FUNAI VHS 31B-254 User Manual
Page 7
7
EN
Channel Presetting
Tuning of broadcast channels not already preset in the VCR
can be performed in two ways.
Automatic Channel Preset
• By “AUTOMATICALLY” tuning channels and placing
them in sequential order in the VCR’s memory i.e. the first
channel found will be memorized into the VCR’s channel
position 1, the second channel found will be memorized
into the VCR’s channel position 2 and so on.
• Execution of the “Automatic” channel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the “Manual”
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
• Each channel is tuned manually and individually. Follow
the steps laid out in the “Manual Channel Preset” section.
Before you preset Channel...
• It is necessary to set the video channel if your VCR is
connected to the TV via the RF cable, and TV channel 35
is set for broadcasting, or interference lines appear on the
picture. Please refer to “Video Channel Setting”.
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
2) Press
MENU
.
3) Press
PLAY
/
K
or
STOP
/
L
to select “INITIAL”, then press
F.FWD
/
B
.
4) Press
PLAY
/
K
or
STOP
/
L
to select “CH TUNING”, then
press
F.FWD
/
B
.
5) Press
PLAY
/
K
or
STOP
/
L
to select “AUTO”, then press
F.FWD
/
B
.
• The tuner scans and memorizes all the active channels in
your area. After scanning, the tuner stops on the lowest
memorized channel.
To Select a Desired Channel
You can select a desired channel by using
CHANNEL
(
K
/
L
), or
directly pressing the
number buttons
on the remote control.
• Enter a channel number as a two-digit number for the
quickest results. For example, to select channel 6, press
0
and
6
. If you only press
6
, channel 6 will be selected after a
brief delay.
• You can only select channels 1–99.
Manual Channel Preset
• Use the remote control for this procedure.
1) Press
MENU
.
2) Press
PLAY
/
K
or
STOP
/
L
to select “INITIAL”, then press
F.FWD
/
B
.
3) Press
PLAY
/
K
or
STOP
/
L
to select “CH TUNING”, then
press
F.FWD
/
B
.
4) Press
PLAY
/
K
or
STOP
/
L
to select “MANUAL”, then
press
F.FWD
/
B
.
5) Press
PLAY
/
K
or
STOP
/
L
to select “POSITION”, then
press
F.FWD
/
B
.
•When a weak signal is received in Manual Tuning mode,
you can change the background to solid blue or the
static screen by pressing
TAPE COUNTER RESET
.
6) Press the
number buttons
,
PLAY
/
K
, or
STOP
/
L
to select
your desired position number, then press
F.FWD
/
B
.
•You can select position number 01-99.
•If [ON] appears on the right side of “SKIP”, press
PLAY
/
K
or
STOP
/
L
to point to “SKIP”. Then, press
F.FWD
/
B
to select [OFF].
•If you want to remove scrambled signals, press
PLAY
/
K
or
STOP
/
L
repeatedly to point to “DECODER”. Then,
press
F.FWD
/
B
to select [ON].
7) Press
PLAY
/
K
or
STOP
/
L
to select “CHANNEL”, then
press
F.FWD
/
B
.
Press
PLAY
/
K
or
STOP
/
L
. The VCR tuner will begin to
search up or down automatically. When a channel is
found, the VCR will stop searching and the picture will
appear on the TV Screen.
•You can select desired channel number by using the
number buttons
. You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press “
0
” button first and then
press “
2
” and “
4
”.)
•If this is the channel you want, press
F.FWD
/
B
.
This VCR can receive Hyper and Oscar frequency bands.
8) Press
MENU
to exit.
Note:
To confirm that a channel has been added, press
CHANNEL
(
K
/
L
).
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
scanning
MENU
TIMER
SET UP
INITIAL
Channel Plan
CH Indication
TV Channel
01 – 10
IRA – IRJ, GAP
21 – 69
E21 – E69
74 – 78
X, Y, Z, Z+1, Z+2
80 – 99, 100
S1 – S20, GAP
121 – 141
S21 – S41
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[OFF]
MENU
TIMER
SET UP
INITIAL
HM210BD(EN).fm Page 7 Thursday, March 2, 2006 6:07 PM