FUNAI VHS 31B-254 - Manual (Page 8)

8
EN
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL ( K / L ).
• Use the remote control for this procedure.
1) Press
MENU .
2) Press PLAY / K or STOP / L to select “INITIAL”, then press
F.FWD / B .
3) Press PLAY / K or STOP / L to select “CH TUNING”, then
press F.FWD / B .
4) Press PLAY / K or STOP / L to select “MANUAL”, then
press F.FWD / B .
5) Press PLAY / K or STOP / L to select “POSITION”, then
press F.FWD / B .
6) Press the number buttons , PLAY / K , or STOP / L to select
relevant position number, then press F.FWD / B .
7) Press PLAY / K or STOP / L to select “SKIP”, then press
F.FWD / B to select [ON].
•To memorize the channel again, press F.FWD / B . “ON”
will change to “OFF”.
Note for 31B-254 and 31B-454 only
•The VCR refers to the PDC channel which was
memorized into position 01 when you set the Auto
Clock.
The position 01 must therefore be set “SKIP” to [OFF].
8) Press MENU to exit.
Note: To confirm that a channel has been deleted, press
CHANNEL ( K / L ).
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
1) Press
MENU .
2) Press PLAY / K or STOP / L to select “INITIAL”, then press
F.FWD / B .
3) Press PLAY / K or STOP / L to select “CH TUNING”, then
press F.FWD / B .
4) Press PLAY / K or STOP / L repeatedly to select “MOVE”,
then press F.FWD / B .
5) Press PLAY / K or STOP / L repeatedly to select the position
number you want to change the channel, then press
F.FWD / B .
•You cannot select a position number where “- - -”
appears next to the number. This is because SKIP is set
to [ON] for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to solid blue by pressing
TAPE COUNTER RESET .
If you press the button again, the background will return
to the static screen.
6) Press PLAY / K or STOP / L repeatedly until the channel
move to another position number, then press F.FWD / B .
7) Press MENU .
INITIAL
CH TUNING
CLOCK
RF OUT
MANUAL
POSITION
CHANNEL
DECODER
SKIP P08
008
[OFF]
[ON]
CH TUNING
AUTO
MANUAL
MOVE
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MOVE
P01:
P02:
P03:
P04:
P05: 01
02
03
04
05 P06:
P07:
P08:
P09:
P10: 06
07
08
09
10
Position
Number
Channel
Number
MOVE
P01:
P02:
P03:
P04:
P05: 01
02
10
04
05 P06:
P07:
P08:
P09:
P10: 06
07
08
09
03
[ ]
MENU
TIMER
SET UP
INITIAL
MOVE
P01:
P02:
P03:
P04:
P05: 01
02
10
04
05 P06:
P07:
P08:
P09:
P10: 06
07
08
09
03
HM210BD(EN).fm Page 8 Thursday, March 2, 2006 6:07 PM