FRIGIDAIRE FASG7074L - Manual (Page 3)

Specifications
subject to change.
Front Load Laundry - Gas Steam Dryer
Frigidaire Affinity (All L Models)
Front Load Dryer Specifications
• Product Shipping Weight (approx.) – 140 Lbs.
• An electrical supply with grounded three-prong receptacle is
required. The power supply circuit must be installed in accordance
with current edition of National Electrical Code (ANSI/NFPA 70)
and local codes & ordinances. (Do not use same circuit as washer.)
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Amps @ 120 Volts = 7 Amps
• Connected Load (kW Rating) @ 120 Volts = 0.5 kW
• Equipped with 120V 3-wire power supply cord, approx. 60" long.
• Always consult local and national electric, gas & plumbing codes.
• Can be installed alone, with or without optional 15" Drawer Pedestal,
or stacked above matching Frigidaire® Affinity Washer, which requires
installation of optional Dryer Stacking Kit. (For installation details, refer
to instructions included with optional pedestal or stacking kit or on web.)
• Can be built in with matching Frigidaire® Affinity Washer in under-
counter, recessed or closet installation. (Refer to Built-In Installations
on this page for cutout dimensions. For additional installation details,
refer to Product Installation Guide on web.)
• Closet installation requires vented door with 2 unobstructed louvered
openings, minimum 60 sq. in. each, located 3" from top and bottom
of door. Full-length 120 sq. in. opening also acceptable. Allow
additional 1" clearance between fronts of units and closed door.
• Do NOT install in area exposed to dripping water or outdoor weather
conditions; where gasoline or other flammables are kept or stored; or
where dryer comes in contact with curtains, drapes or anything that
will obstruct flow of combustion and ventilation air.
• For garage installation, dryer MUST be located minimum 18" above floor.
• Floor MUST be solid with 1" maximum slope. Do NOT install on
carpeted surface.
• Dryer MUST exhaust to outside of building, NOT into any concealed
space.
• Exhaust installation requires minimum 4"-diameter rigid or flexible
metal duct with approved vent hood having swing-out damper(s). Do
NOT use flexible plastic or metal foil duct and use shortest run possible.
• Gas supply line should be 1/2" pipe and MUST have individual
shutoff valve.
• Leveling legs supplied to level dryer properly and reduce excessive
noise and vibration.
• Water inlet hose for steam setting connects to cold water supply
with “Y” connector and requires 3/4" clearance between back of unit
and wall.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
• Dryer Stacking Kit – (PN # STACKIT4X).
• 15" Classic Red Drawer Pedestal – (PN # CFPWD15R).
• 15" Classic Blue Drawer Pedestal – (PN # CFPWD15N).
• 15" Classic Silver Drawer Pedestal – (PN # CFPWD15A).
• 15" Classic White Drawer Pedestal – (PN # CFPWD15W).
• Mobile Home Installation Kit – (PN # 137067200).
• LP Gas Conversion Kit – (PN # PCK4200).
• Drying Rack – (PN # 137067300).
USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca
FASG7074L 10/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
Front Load Dryers
FASG7074L R / N / A / W 7.0 Cu. Ft. Gas