Fostex D2424LVMKII - Manual (Page 21)

Model D2424LVmkII Quick Operation Guide
22
<Selecting the desired Program>
If you have set up multiple Programs on the disk,
you first need to select the target Program prior to
recording, playback, or edit. To select a Program,
follow the steps below. Do not select a different
Program until you finish the session.
1. While this recorder is stopped, press the [PGM
SEL] key.
“ Select PGM! ” appears momentarily, then the
number and title of the current Program appear.
2. Turn the Jog dial clockwise or counter-clockwise.
The numbers and titles of the Programs on the
disk appear in turn.
3. Select the desired Program number and press
the [EXECUTE/YES] key.
The top of the selected Program appears in ABS
Time Base (ABS 0).
Recording in a new Program
1. While this recorder is stopped, press the [PGM SEL]
key.
The display indicates “ Select PGM! ” momentarily, then
shows the title of Program 1. The Program number
and “
SURE? ” flash.
2. Turn the Jog dial clockwise to select “New Program?”.
The “ ? ” mark of “ New Program? ”, and “ SURE? ” flash,
indicating that you can set up a new Program.
3. Press the [EXECUTE/YES] key.
This recorder sets up a new Program (Program 2) and
enters the “
Title Edit? ” menu in SETUP mode, showing
the following display. In this example, we use the
default title.
You can change the title later. Refer to the Reference
manual for more information.
4. Press the [EXIT/NO] key.
This recorder exits SETUP mode, and the top of
Program 2 in ABS Time Base (ABS 0) appears.
Normally, any new program that is compiled will be in the
sampling frequency set when formatting the current drive.
However, in this recorder, it is possible to change the program
sampling frequency.
In other words, programs with different sampling frequencies
can be made in the current drive and thus recording can be
matched to a chosen task. For details refer to the next page.
The explanation so far has been based on one Program set up when you format a current drive (E-IDE hard
disk). You may create up to 99 Programs, depending on the available disk space.
Multiple Programs do not interfere with each other. You can record, play, and edit each Program independently,
which facilitates song management. This section explains how to set up a new Program on the disk. Refer to
the reference manual for more information regarding Programs.
∞ 42
OL 0
30 24 18 12
9 6 3
kHz
24
FS
BIT
PGM
24
∞ 42
OL 0
30 24 18 12
9 6 3
SURE?
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
∞ 42
OL 0
30
24
18 12
9 6
3
kHz
24
FS
BIT
PGM
24
∞ 42
OL 0
30
24
18 12
9 6
3
SURE?
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
∞ 42
OL
0
30
24 18
12 9
6
3
kHz
24
FS
BIT
SETUP
PGM
24
∞ 42
OL
0
30
24 18
12 9
6
3
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
F S M
∞ 42
OL 0
30 24
18 12
9
6 3
kHz
24
FS
BIT
PGM
24
∞ 42
OL 0
30 24
18 12
9
6 3
ABS
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
<CAUTION>
• When creating a new program, the initial settings such as the tempo map are copied from the current
program. For example, if the default tempo map is edited in the current program, the edited tempo map is
copied to the newly created program.
• A new compilation is possible only when the “ Chain Play? ” (Setup of the chain play mode) menu in the
SETUP mode is set to “ Off.” If the [PGM SEL] key is pressed when the “ Chain Play? ” menu is set in other than
the “ Off ” mode, the recorder will enter the “ Chain Play mode ”. Before starting compilation, check that the
“ Chain Play? ” is “ Off” and if it is not, be sure to reset it to “ Off.”
Flashing Flashing
Flashing Flashing
Flashing