Changing the program fs, Current drive formatting by 24bit, Current drive formatting by 16bit – Fostex D2424LVMKII User Manual
Page 22: Model d2424lvmkii quick operation guide, Track numbers 1 through 8 are lit, The display will change to setup mode
Model D2424LVmkII Quick Operation Guide
23
Changing the program FS
In the following, we will change a program’s sampling frequency in the current drive.
IN general, the sampling frequency of the program made in the current drive will be the value set during the
most recent formatting of the current drive. But even after a program has been made, the sampling frequency
can be changed. However, the changes will be limited as follows depending on the quantizing figure when
formatting.
<Note>
• Do not change the sampling frequency of a completed program.
• Changing of the sampling frequency will be limited by the quantizing figure (16bit or 24bit) set at
formatting of the current drive.
Current drive formatting by 24bit:
A program in 44.1kHz, 48kHz, 88.2kHz or 96kHz can be made.
Current drive formatting by 16bit:
A program in 44.1kHz or 48kHz can be made.
• Please remember the following points should there be programs with a different FS in the current
drive.
* Do not copy or paste between programs with different FS. Fostex cannot take responsibility in
compensation of data which had been “copied” or “pasted” between programs with different FS.
* In the section “Digital recording” explained above, be sure to set the external digital equipment
sampling frequency the same as that of the program.
1.
First, start the program in which the FS is to be
changed by using the “program change” menu
explained above.
2.
Press the [SETUP] key to enter the SETUP mode.
The display will change to SETUP mode.
3.
Rotate the Jog dial to display the “Sample Rate?”
menu and then press the [EXECUTE/YES] key.
When the
[EXECUTE/YES]
key is pressed, the FS figure
of the current activated program will flash and the
recorder will enter the editing mode.
4.
Display the desired FS by rotating the Jog dial, an
then press the [EXECUTE/YES] key.
Either “44.1” or “48” can be selected in the 16bit
current drive, “44.1,” “48,” “88.2,” or “96” can be
selected in the 24 bit current drive. After selection,
the recorder will be set to the chosen FS when the
[EXECUTE/YES]
key is pressed.
5.
Exit from the SETUP mode by pressing the [EXIT/NO]
key or [STOP] button.
<Note>
If you change the FS (44.1 or 48kHz) of a
program in the 24-track mode to 88.2 or
96kHz, the program automatically changes
to the 8-track mode and track numbers 1
through 8 on the display are lit.
The following shows display examples when
changing the FS of a 48kHz/24bit program
to 96kHz.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
F
S
M
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
F
S
M
∞
42
OL
0
30
24
18
12
9
6
3
kHz
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
ABS
8
7
6
5
4
3
2
1
CLOCK
INT
Track numbers 1 through 8 are lit.
Flashing
Flashing