Fluke 430 Series - Manual (Page 5)

Specifications
continued
Accuracy, resolution and range
Volt/Amps/Hertz Measurement range Resolution Accuracy
Vrms (AC+DC) 1 to 1000 Vrms 0.1 Vrms ± 0.5 % of nominal voltage
Vpk 1 to 1400 Vpk 1 V 5 % of nominal voltage
CFV 1.0 to > 2.8 0.1 ± 5 %
Arms (AC+DC) 0 to 20,000 Arms 1 0,001 to 10 Arms 1 ± 1 % of reading ± 5 counts 3
with included clamps 0 to 400 Arms 0.1 and 1 Arms
Apk using 1mV/A scaling 0 - 5500 Apk 10 A ± 5 %
CFA using 1mV/A scaling 1 to 10 0.1 ± 5 %
50 Hz nominal 42.50 to 57.50 Hz 0.01 Hz ± 0.1 % of nominal frequency
60 Hz nominal 51.00 to 69.00 Hz 0.01 Hz ± 0.1 % of nominal frequency
Dips and swells
Vrms 1 ⁄
2
(AC+DC) 0.0 to100 % of nominal voltage 0.1Vrms ± 1 % of nominal voltage
Arms 1 ⁄
2
(AC+DC) 0 to 20,000 Arms 1 0,001 Arms to 10 Arms ± 1 % of reading ± 5 counts 3
with included clamps 0 to 400 Arms 0.1 Arms and 1 Arms
Threshold levels Programmable in percent of nominal voltage
Duration hhh,mm,ss,mmm with half-cycle cycle time resolution
Harmonics
Harmonic selection (n) DC, 1 to 50
Inter-Harmonic selection Off, 1 to 49
Vrms Relative (%f): 0.0 to 100.0 % 0.1 % ± 0.1 % ± n x 0.1 %
(± 0.4 % for %r)
Absolute: 0.0 to 1000 Vrms 0.1 Vrms ± 5 % of reading ± 2 counts
Arms Relative (%f): 0.0 to 100.0 % 0.1 % ± 0.1 % ± n x 0.1 %
(± 0.4 % for %r)
Absolute: 0.0 to 4000 mV x selected 1 mVrms x selected clamp scaling ± 5 % of reading ± 5 counts
clamp scaling
Watts Relative: 0.0 to 100.0 % 0.1 % ± n x 2 %
Absolute: depends on selected clamp ± 5 % of reading ± n x 2 %
and voltage scaling of reading, ± 10 counts
DC voltage Relative: 0.0 to 100.0 % 0.1 % ± 1 %
Absolute: 0.0 to 1000 V 0.1 V ± 5 % of reading ± 10 counts
THD 0.0 to 100.0 % 0.1 % ± 2.5 %
Hz 0 to 3500 Hz 1 Hz ± 1Hz
Phase angle -360 º to +360 º 1 º ± n x 1.5 º
Power and Energy
Watt 1.0 W to 20.00 MW 1 0.1 W to 1 kW 1 ± 1.5 % of reading ± 10 counts 3
VA 1.0 VA to 20.00 MVA 1 0.1 VA to 1 kVA 1 ± 1.5 % of reading ± 10 counts 3
VAR 1.0 VAR to 20.00 MVAR 1 0.1 VAR to 1 kVAR 1 ± 1.5 % of reading ± 10 counts 3
kWh 00.00 kWhr to 200.0 GWhr 1 0.01 Whr to 100 Whr 1 ± 1.5 % of reading ± 10 counts 3
kVA 00.00 kVAhr to 200.0 GVAhr 1 0.01 VAhr to 100 VAhr 1 ± 1.5 % of reading ± 10 counts 3
kVAR 00.00 kVARhr to 200.0 GVARhr 1 0.01 VARhr to 100 VARhr 1 ± 1.5 % of reading ± 10 counts 3
Power Factor 0 to 1 0.01 ± 0.03 3
Cos ϕ / DPF 0 to 1 0.01 ± 0.03 3
Flicker
Pst (1min), Pst, Plt, PF5 0.00 to 20.00 0.01 Within ± 5 % of tabulated values
instantenous Flicker according IEC61000-4-15
Dc %, Dmax % and Time d(t) 0.0 to ± 100.0 % for Dc % and 0.1 % for Dc % and Dmax % and ± 1% for Dc % and Dmax % and
exceeds limits. As described Dmax % and 0.000 to 9.999s 10 ms for Time 20 ms for Time
per IEC 61000-3-3 for Time
Unbalance
Volts 0.0 to 5.0 % 0.1 % ± 0.5 %
Current 0.0 to 20 % 0.1 % ± 1 %
Transient capture
Volts ± 6000 Vpk 1 V ± 15 % of cursor reading
± 2.5 % of Vrms
Minimum detect duration 5 µs Sampling rate 200 kS/s
Inrush mode
Arms (AC+DC) 0.000 to 20.00 kArms 1 0.001 to 10 Arms 1 ± 1 % of meas ± 5 counts 3
Inrush Duration mm:ss:mmm between 7.5 s to 10 ms ± 20 ms (Fnominal = 50 Hz)
30 m selectable
Fluke 430 Series Three-Phase Power Quality Analyzers Fluke Corporation 5