FUNAI TB110MW9 - Manual (Page 14)

14
EN
Initial Setup (Setup Wizard) up (Setup W
3 Select “CONTINUE” using [
s / B],
then press [OK].
Seleccione “CONTINÚE” utilizando [ s / B] y presione
[OK].
“CONTINUE”:
“CANCEL ”:
CONTINUE CANCEL
To continue setup
To cancel to leave pre-arranged
setup
This SETUP WIZARD will help you with the initial
setup on your own.
4 Select the language using [
K / L],
then press [OK].
Seleccione el idioma utilizando [ K / L] y presione [OK].
Select the language for setup display.
Elija idioma de preparación.
Sélectionner langue écran config.
ESPAÑOL
ENGLISH
FRANÇAIS
5 Select the connection for audio
output using [
s / B], then press [OK].
Seleccione la conexión para salida de audio mediante
[
s / B] y luego presione [OK].
AUDIO OUT :
RF OUT :
Connecting STB and TV via AUDIO
Cable
Connecting STB and TV via RF
Cable
AUDIO OUT RF OUT
Select the connection for Audio output.
Select “AUDIO OUT” if...
- you are using the standard audio cable to
connect the STB to your TV. (Connection B or
C on pages 10 and 11.)
Seleccione “AUDIO FUERA” si...
- está utilizando el cable de audio normal para
conectar el STB a su TV. (conexión B o C en las
páginas 10 y 11.)
Select “RF OUT” if...
- you are using the RF cable to connect the STB
to your TV. (Connection A or D on pages 10
and 12.)
Seleccione “RF FUERA” si...
- está utilizando el cable RF para conectar el STB a su
TV. (conexión A o D en las páginas 10 y 12.)
6 Select your time zone using [
K / L],
then press [OK].
Seleccione su huso horario con [ K / L] y presione [OK].
Select Time Zone.
ATLANTIC
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
EASTERN
7 Select “ON” or “OFF” for Daylight
Saving Time (D.S.T) using [
s / B ],
then press [OK].
Seleccione “ON” u “OFF” para la hora de verano. (D.S.T)
utilizando [
s / B] y presione [OK].
Select Daylight Saving Time.
NOTE:
2:00AM of the second Sunday in
March until 2:00AM of the first
Sunday in November.
OFF ON
8 Select the desired display mode
using [
K / L ], then press [OK] (refer
to page 20).
Seleccione el modo de indicación deseado utilizando
[
K / L] y presione [OK].
Select display mode.
ZOOM
FULL
LETTERBOX
9 Select “AUTOSCAN” using [
K / L ],
then press [OK].
Seleccione “AUTOEXPLO.” mediante [ K / L] y luego
presione [OK].
AUTOSCAN will rescan all channels.
This may take a while to complete.
EXIT
AUTOSCAN
The system is now scanning.
12% Channel Found
EXIT
•
STB starts receiving available digital channels
and stores them in the channel map.
•
When the scanning is complete,
“AUTOSCAN COMPLETED” will be indicated.
•
After autoscan is complete, use [CH K / L ]
to verify whether STB is receiving channels
properly.
The “SETUP WIZARD” is now complete.
El “ASISTENTE DE PREP.” ahora ha fi nalizado.
To cancel during scanning:
Press [SETUP] or [OK].
Para cancelar durante la exploración: Presione [SETUP] o [OK].
•
If autoscan is canceled, some channels not yet
scanned may not be received. We recommend
completing autoscan.
•
You can do autoscan and adding / deleting
channel later. Refer to page 18.