Document Outline

• Contents
• Introduction
  • Introduction
  • Features
    • Gateway E-824R DLT-V4 SuperLoader3
    • Gateway E-826R LTO-3 SuperLoader3
    • Bar code reader
    • Accessories
  • Enclosure components
    • Front
    • Back
    • Product components
  • Getting Help
    • External Backup CD
    • Gateway Web site
• Installing and Setting Up your Autoloader
  • Overview
  • Preparation
    • Choosing a location
    • UL requirements
    • Unpacking the autoloader
  • Installation
    • Rack mounting the autoloader
    • General preparation for rack mount installation
    • Installing and removing the V-rail kit
    • Connecting the SCSI and power cables
    • Preparing the host and making sure the connection is correct
    • Installing the device drivers
  • Setup
    • Configuring the autoloader
    • Setting the time
    • Setting the Change mode
• Operating your Autoloader
  • Using the operator's panel
    • Entering the passwords
    • Logging out
  • Using cartridges
    • Inserting a single cartridge
    • Moving a single cartridge
    • Ejecting a single cartridge
  • Using magazines and magazine blanks
    • Magazine Load/Unload command
    • Installing a magazine
    • Installing a magazine blank
    • Removing a magazine
    • Removing a magazine blank
    • Changing the orientation of a magazine or magazine blank
    • Manually operating the magazine
  • Replacing a magazine or magazine blank
  • Viewing status information
    • Viewing the autoloader status
    • Viewing the firmware version
    • Viewing the status of the magazine slots
    • Viewing the tape drive status
    • Viewing the tape drive version
    • Viewing Ethernet information
  • Running an inventory
  • Data compression
• Managing and Monitoring your Autoloader
  • On-board Remote Management overview
    • Opening On-board Remote Management
    • Viewing status information
    • Feedback on pages
  • Using the Configuration page
    • System Operations options
    • Setting security options
  • Using the Updates page
  • Using the Diagnostics page
    • Running diagnostic tests
    • Viewing Error or History logs
    • Diagnostics
    • Identification
    • Performing a System Reset
  • Using the Commands page
    • Inventory
    • Set to Home
    • Sequential operations
• Troubleshooting your Autoloader
  • Overview
  • Safety guidelines
  • Understanding POST
    • Performing a POST
    • Interpreting the POST results
  • Running diagnostic tests from the front panel
    • Setting the security
    • Stopping a diagnostic test
    • Front panel diagnostic tests
  • Running diagnostic tests remotely
    • Diagnostics using On-board Remote Management
  • Checking for errors
    • Hard error log display
    • Error code field description
  • Before contacting Gateway Customer Care
  • Telephone support
    • Tutoring and training
  • Returning the autoloader for service
    • Preparing the autoloader for shipment
    • Removing the autoloader from a rack
    • Packing the autoloader
• Logs
  • Basic information logs
  • Log descriptions
    • Autoloader logs
  • Error codes
    • Soft logs
    • Update logs
    • Boot logs
  • Tape drive logs
    • Tape drive error logs
    • SCSI check condition error logs
  • POST failure logs
• Specifications
  • Physical specifications
  • Autoloader performance specifications
  • Environmental specifications
  • Autoloader power specifications
  • Autoloader vibration specifications
  • Autoloader shock specifications
  • Tape drive specifications
    • LTO-3 drive specifications
    • DLT-V4 drive specifications
• Safety, Regulatory, and Legal Information
• Index
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • O
  • P
  • R
  • S
  • T
  • U
  • V
  • W