Stovax Marlborough & Stockton Coal Effect Stove Range - Manual (Page 5)

5
THE YELLOW FLAMES WILL APPEAR WHEN THE FIRE
HAS REACHED SUFFICIENT HEAT - TYPICALLY 10 TO 20
MINUTES.
IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN
USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO
RE-LIGHT THE APPLIANCE.
3. TURNING THE STOVE OFF
3.1 To turn the stove off, locate the control valve, turn the left-
hand control knob until it points to off ( ). The main burner
goes out leaving the pilot burning.
3.2 To turn the pilot off, locate the control valve, turn the right-
hand control knob until it points to off ( ), the pilot goes out.
4. UPGRADING YOUR STOVE
4.1 Your stove is fitted with a control valve that can easily be
upgraded to battery powered remote control. This upgrade can
be fitted by anyone capable of simple DIY jobs and requires no
special training. There are two versions of this control which
can be obtained through your local Gazco stockist.
4.2 STANDARD REMOTE CONTROL. This remote controls the
gas appliance after the pilot has been lit. It can turn the
main burner on and regulate it from low through to high
and back again. It can turn the main burner off leaving the
pilot burning GAZCO PART NUMBER 8455.
4.3 THERMOSTATIC AND TIMER REMOTE CONTROL. This
remote controls the gas appliance after the pilot has been
lit. In ‘MANUAL MODE’ it can be used to turn the main
burner on and manually regulate it from low through to
high and back again. It can also be used to turn the main
burner leaving the pilot burning. In ‘AUTO MODE’ it will
automatically regulate the room temperature to a pre-set
temperature. In ‘TIMER MODE’ it will turn the fire on and
off according to a pre-set programme and automatically
regulate the room temperature during the two ON periods.
GAZCO PART NUMBER 8456.
5. CLEANING THE FIRE
WARNING: DO NOT ATTEMPT TO CLEAN THE STOVE
UNTIL IT IS COLD. THE STOVE RETAINS ITS HEAT FOR
A CONSIDERABLE TIME AFTER SHUTDOWN.
NOTE: THE CAST IRON DOOR IS HEAVY, TAkE
EXTREME CARE WHEN HANDLING.
5.1 Remove the door by undoing the four dome nuts using the
tool supplied and place to one side.
5.2 Carefully remove the ceramic fuel bed components and
place to one side taking care to protect floor coverings etc,
PLEASE HANDLE WITH CARE.
5.3 The coals should not require cleaning. Do not use a vacuum
cleaner or brush to clean the coals, any large pieces of
debris can be removed by hand.
5.4 Ensure any debris is removed from the burner ports.
5.5 Replace the ceramics by referring to section 6.
5.6 Use a damp cloth to clean the outer casing of the
appliance.
Advice on Handling and disposal of fire ceramics
5.7 The fuel effect and side panels in this appliance are made
from Refractory Ceramic Fibre (RCF), a material which is
commonly used for this application.
Protective clothing is not required when handling these
articles, but we recommend you follow normal hygiene
rules of not smoking, eating or drinking in the work area
and always wash your hands before eating or drinking.
To ensure that the release of RCF fibres are kept to a
minimum, during installation and servicing a HEPA filtered
vacuum is recommended to remove any dust accumulated
in and around the appliance before and after working on it.
When servicing the appliance it is recommended that the
replaced items are not broken up, but are sealed within
heavy duty polythene bags and labelled as RCF waste.
RCF waste is classed as stable, non-reactive hazardous waste
and may be disposed of at a licensed landfill site.
Excessive exposure to these materials may cause temporary
irritation to eyes, skin and respiratory tract; wash hands
thoroughly after handling the material.
6. FUEL BED ARRANGEMENT
The major ceramic components can be found inside the
firebox. Remove the cast iron door using the tool provided,
and remove all the protective packaging from these
components. See Diagram 3.
NOTE: THE CAST IRON IS HEAVY, TAkE EXTREME CARE
WHEN HANDLING.
The loose coals should be arranged as specified in the
following steps. Care should be taken to ensure that there is
sufficient space between the coals to allow flames to pass
through.
USER INSTRUCTIONS