Gardena 1243 User Manual
Page 8
31
G
30
G
3. Set the arrow V to the sensor you require (e.g. V 7 =
sensor 7) using the
▲-▼ keys and assign the sensor to the
channel (e.g. V
■ 7) by pressing the OK key.
4. Once you have assigned all the sensors you require (e.g.
■ 1
and
■ 7), to the channel (e.g. channel
99
) press the Menu +.
The display then changes to point 2 again and the channel and
the sensors assigned to this channel are displayed.
8.10 Temperature Sensor
Each radio receiver is equipped with a temperature sensor in
addition to the connected sensors. The temperature of the con-
nected receiver is displayed in the main level.
1. Select the radio receiver In the main level using the
▲-▼ keys.
TEMP
is displayed and the arrows V flash next to the selected
radio receiver.
2. Confirm by pressing OK (e.g. radio receiver V 6 to V 9 ).
The temperature is displayed as -- ° C until the radio receiver has
transferred the current temperature of the Central Radio Control
Unit (e.g.
2255
°C).
8.11 Channel and Sensor View
The main level can be displayed in the channel or sensor view.
v Press the Channel Sensor key to change the view.
a) Channel View :
CHANNEL
and all channels that are switched on are displayed
(e.g. channels 1, 3 and 7 are switched on
■ 1, ■ 3 and ■ 7).
b) Sensor View :
SENSOR
and all sensors that are switched on are displayed,
e. g. Soil Moisture Sensor = moist
(e.g. sensors 3 and 9 are switched on =
■ 3 and ■ 9).
8.7 Changing the Default Manual Opening Time
The default value for the manual opening time can be set
between
00::0011
and
99 ::5599
. The Central Radio Control Unit is
pre-set to
00::3300
.
1. Press the Setup key (e.g. using the tip of a pen).
SETUP
is displayed and the free channels flash on the display.
2. Press and hold down the Man On / Off key for approx.
3 seconds.
MAN
and
RUN-TIME
are displayed and the hours of the opening
time flash.
3. Set the hours for the opening time using the
▲-▼ keys
(e.g.
11
) and confirm by pressing the OK key.
4. Set the minutes for the opening time using the
▲-▼ keys
(e.g.
1100
) and confirm by pressing the OK key.
8.8 Changing the PIN
The 3-digit PIN (Personal Identification Number) which can be
set between
000000
and
999999
, prevents unauthorised access to
your watering programmes. You are only asked to enter your PIN
if the number is not
000000
.
1. Press the Setup key (e.g. using the tip of a pen).
SETUP
is displayed and the free channels flash on the display.
2. Press and hold down the Channel Sensor key for approx.
3 seconds.
PIN
is displayed and the first number of the PIN flashes.
3. Set the first number of your PIN using the
▲-▼ keys (e.g.
99
)
and confirm by pressing the OK key.
4. Change the second digit (e.g.
77
) and the third digit (e.g.
33
)
in the same way as for the first digit.
When you have changed the PIN, the main level appears on
the display again.
8.9 Operating the Sensors
After registering the receiver, each channel is assigned its own
sensor (sensor 16
(M)
was registered together with channel
M
).
The sensors can also be assigned to the channels individually.
This is useful, for example, if you want to control the entire irri-
gation system using a rain sensor or soil moisture sensor.
1. Press and hold down the Channel Sensor key for 2 seconds.
SENSOR
is displayed, Channel
11
and
CHANNEL
flash on the
display.
2. Select the channel using the
▲-▼ keys (e.g. channel
99
)
and confirm by pressing the OK key.
SENSOR
and the arrow V next to sensor 1 (V 1) flash on
the display.
1.
2.
3.
4.
3.
4.
3.
4.
1.
2.
a) b)