MTD 769-01276A - Manual (Page 25)

25
Styles H & K
* One found between spirals on models with 24-inch auger housing.
* Three found between spirals on models with 28-inch auger housing.
** One found between spirals on models with 30-inch auger housing.
^ Three found on models with 30-inch auger housing.
† H-Style
†† K-Style
‡ If Equipped
NOTE:
Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
REF.
NO.
PART
NO. DESCRIPTION
1 731-2643 Clean Out Tool
2 684-04057 Impeller Assembly, 12” Dia
3 710-0347 Screw, 3/8-16 x 1.75, Gr5, Std
4 710-0451 Bolt, Carriage, 5/16-18 x.750 Gr1
5 710-0703 Screw, Carriage, 1/4-20 x.75, Gr5
6 710-0726 Screw, 5/16-12 x 0.750
7 712-04063 Nut, Flange Lock, Nylon, 5/16-18, GrF
8 712-04064 Nut, Flange Lock, Nylon, 1/4-20, GrF
9 712-04065 Nut, Flange Lock, Nylon, 3/8-16, GrF
10 714-0507 Pin, Cotter, 3/32 x.750
11 725-0157 Cable, Tie, 3/16 x.05 x 7.4
12 726-04012 Nut, Push-on,.25 Dia
13 731-04705 Chute, Adapter 5” Dia
14 732-0611 Spring, Extension,.38 OD x 3.6
15 736-0174 Washer, Wave,.625 x.885 x.015
16 736-0463 Washer, Flat,.25 x.630 x.0515
17 731-04869 Keeper, Flange
18 738-0143 Screw, Shoulder,.498 x.340, 3/8-16
19 738-0281 Screw, Shoulder,.625 x.17, 3/8-16
20 738-04124 Pin, Shear,.25 x1.50, Gr2
21 741-0245 Bearing, Hex Flange x.75 ID
22 741-0309 Bearing, Ball,.75 ID x 1.85 OD
23 756-0981A Pulley, Idler, Flat 2.75 OD
24 790-00075 Housing, Bearing, 1.85 ID
25 790-00080 Bracket, Auger Idler w/ Brake
26 631-04131 Chute Assembly, Lower, 2-way
(Inc. Ref 17, Qty. 3)
27 741-0475 Plastic Bushing
28 710-0451† Bolt, Carriage, 5/16-18,.750, Gr1
710-0262†† Bolt, Carriage, 5/16-18, 1.50, Gr2
29 710-04071 Bolt, Carriage, 5/16-18, 1.00
30 720-0284† Knob Assembly
31 710-0895†† Screw, 1/4-15 x 0.75
32 736-0159 Flat Washer,.349 x.879 x.063
33 784-5647 Chute Directional Control Bracket
34 746-0897 Auger Clutch Cable, 44.75”
35a 784-5580 Shoe, Slide, Standard
35b 790-00091‡ Shoe, Slide, Deluxe
36 629-0071 Extension Cord, 3-Prong
37 731-04426A† Upper Chute, Manual
731-04427A†† Upper Chute, Remote
38 731-1313C Cable Guide, Chute Tilt
39 731-2635 Mount, Clean Out Tool
40 784-5594†† Cable Bracket (Cables not included)
41 741-0663 Bearing, Flange,.75 ID x 1.00 OD x.925
42 618-04171 Gearbox Assembly, Auger, 24”
618-04173 Gearbox Assembly, Auger, 28”
618-04165 Gearbox Assembly, Auger, 30”
43 684-04069 Housing Assembly, Auger 24”
684-04073 Housing Assembly, Auger 28”
684-04063 Housing Assembly, Auger 30”
44 684-04107^ Spiral Assembly, LH
45 684-04108^ Spiral Assembly, RH
46 731-04870* Spacer, 1.25 OD x.75 ID x 1.00
731-04871** Spacer, 1.25 OD x.75 ID x 3/16
47 736-0188 Washer, Flat,.76 x 1.49 x.06
48 736-3084 Washer, Flat,.51 x 1.12
49 721-0179 Seal, Oil,.750 ID
50 741-0493A Bushing, Flange,.800 ID x.910 OD
51 790-00120 Plate, Shave, 24”
790-00118 Plate, Shave, 28”
790-00119 Plate, Shave, 30”
52 790-00087 Housing, Bearing, 1” Hex
53 618-0123 Housing Assembly, Auger, RH Reducer
(Inc. Refs. 49 & 55)
54 618-0124 Housing Assembly, Auger, LH Reducer
(Inc. Refs. 49 & 55)
55 741-0661A Bearing, Flange,.75 ID x 1.00 OD x.975
56 717-0528A Gear, Worm 20T
57 736-0351 Washer, Flat,.760 ID x 1.5 OD
58 714-0161 Key, Hi-pro 3/16 x 5/8
59 715-04021 Pin, Dowel,.25 OD x 1.2
60 721-0325 Plug, 1/4 x.437
61 711-04285 Axle, Auger, 24"
711-04283 Axle, Auger, 28"
711-04282 Axle, Auger, 30"
62 710-0642 Screw, Self-tapping, 1/4-20, 0.750
63 741-0662 Bearing, Flange,.75 ID x 1.00 OD x.59
64 717-04126 Shaft, Worm.75 OD
65 718-04071 Collar, Thrust
66 721-0327 Seal, Oil,.75 x 1 x.131
67 710-0276 Carriage Screw, 5/16-18 x 1.00
68 746-0901 Chute Deflector Cable w/Clip
69 746-0896 Chute Deflector Control Cable
70 736-0242 Bell Washer
REF.
NO.
PART
NO. DESCRIPTION