Marantz SR7200 - Manual (Page 21)

14
ENGLISH OTHER FUNCTIONS
SETTING THE SLEEP TIMER
Set the sleep timer while the power is turned on.
1. Turn the power ON and press the SLEEP button o .
2. Press the SLEEP button o the number of times to set the desired
sleep time in minutes.
Each press of the
SLEEP button o or changes the display in the
following order:
The unit will shut off in the number of minutes indicated.
* While the sleep timer is activated, the remaining time can be
displayed for approximately 2 seconds by pressing the SLEEP
button o .
* To cancel the sleep timer, press the SLEEP button o and then
press the CLEAR button !3 .
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the TV IN jack to
control the power (ON/OFF) to the SR7200.
AUTO POWER ON
1. Be sure TV auto mode is enable. (Refer page 9 : System Setup 1/3)
2. Connect your TV TUNER (etc) to the TV IN terminal.
Be sure to connect the video input.
3. Turn OFF the power to the TV TUNER and the SR7200 will be in
standby mode.
4. Turn ON the TV TUNER and tune in a receivable station.
5. When the station is received, the SR7200 turns ON and TV is
selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF or select a
channel that does not contain any broadcast.
2. The SR7200 switches to STANDBY after approximately 5
minutes.
Note:
AUTO POWER OFF is canceled if the FUNCTION SELECTOR
button t is set to a source other than TV. The function reactivates
when TV is selected again.
Caution:
Some TV broadcasts may cause the TV AUTO FUNCTION to be
turned enable. To set this function to ENABLE/DISABLE, refer to
the SETUP MENU.
10 20 30
(OFF) 90 60
MULTI ROOM SELECTOR
The Multi Room Selector is a function which allows you to listen to the
same or a different source in a room other than the room in which the
SR7200 is located. To use this function, a multi room remote unit and
remote control signal receiver available from your Marantz dealer are
necessary. The operations possible with the multi room function are
explained briefly below. For details, refer to the instruction manual
supplied with the multi room remote control unit and receiver.
MULTI ROOM SELECTOR OPERATION
1. Press the MULTI ROOM button !1 . The unit enters multi room
mode and the display indicates “SEL SOURCE” and flashes the
“MULTI ROOM” indicator for approx. 5 seconds. In this time, you
can select the input source by pressing the
FUNCTION
SELECTOR button t .
2. Then, the display indicates “M/VOL xx dB”. At this time, you can
set the volume level of the multi room by turning the volume
control knob.
3. Then, the display indicates “M/SLEEP OFF” and you can set
sleep timer for multi room by pressing by the
SLEEP button o
MULTI ROOM SELECTOR OPERATION (USING THE MULTI
ROOM REMOTE CONTROL UNIT)
1. If Video output for multi room is connected to the TV in your
second zone, the on screen display for this video signal will be
shown as follow.
2. Press the MULTI ROOM button !1 , the POWER ON button, or
select the desired source on multi room remote control unit from
the MULTI ROOM. Any of these operations will put the SR7200
into multi room mode and “MULTI ROOM” indicator will light and
OSD system for the TV in the multi room will be shown.
3. Press the VOL.UP or VOL.DOWN button on the multi room
remote control unit to set the desired sound volume.
4. In multi room mode, the multi room remote control unit can be
used in the multi room to operate the following functions.
You can select a tuner preset channel and tuning up or down, and
direct selection. And you can control the CD player, DVD player
VCR and tape deck connected to the SR7200.
5. Additionally, SLEEP timer function for multi room is available from
second zone, by the same way as setting the sleep timer for main
room.
6. The status of the main room setting can be monitored from the
second zone with the OSD.
Caution:
If the main room and the secondary room are listening to the same
source, the main room will have priority over controlling that
source. For example, you cannot change the frequency or preset of
the Tuner from a remote location if the main room is also listening
to that source.