Marantz SR7200 - Manual (Page 28)

21
ENGLISH
REWRITING NAMES
This remote controller allows the names accessible by Jog Dial
control n to be rewritten with new ones of your choosing.
• Rewriting of names is performed for each individual function.
• Let’s use a DVD player as an example to show how to change the
’s “OSD” to “F-OSD”.
1. Use a ballpoint pen or other sharp point to press the MODE button
z to switch the remote controller to the NAME mode. The NAME
indicator blinks.
2. Press the DVD Function button ,.
3. Use the Jog Dial n to select the page for which you wish to enter
a new name.
4. The character on the left-hand side of the Command Name
indicator on LCD b will flash, indicating that it is the character
ready to be rewritten. New characters entered will be written over
the top of the current character so that the current character is
erased.
Use the < and > Cursor buttons ⁄0 to select the characters to be
rewritten.
5. Use the ten-key pad ⁄7to select the desired alphanumeric
characters.
Pressing the number buttons on the ten-key pad will cycle through
the alphanumeric characters as follows:
Ten keypad Press, press again, press again, etc.
1 A → B → C → 1 → A
2 D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 S → T → U → 7 → S
8 V → W → X → 8 → V
9 Y → Z → / → 9 → Y
0 SPACE → + → — → , → ’ → 0 →SPACE ( )
6. For example, to enter the letter “F”, press the 2-key on the ten-key
pad ⁄7 3 times in a row to cycle from D to E to F.
Once the desired character “F” appears, press either of the < and
> Cursor buttons ⁄0 and the “F” will be permanently written over
the former character. Press the 0-key in order to replace
unneeded extra characters with spaces.
7. Follow the same procedure to enter “-OSD”. When finished, press
the OK Cursor button ⁄0. Pressing OK permanently fixes the
newly written characters.
• Up to 5 alphanumeric characters may be entered in the
Command Name indicator of the LCD.
• To rewrite the names of the other items in the Command
Name indicator, use the Jog Dial n to select the desired
command and repeat from step 5.
8. When you are finished rewriting, use a ballpoint pen or other sharp
point to press the MODE button z to return the remote controller
to the USE mode. The USE indicator is displayed on the LCD,
and the newly programmed codes now can be used.
ERASING PROGRAMMED CODES
(Returning to Factory Presets)
Codes that have been programmed into the memory can be erased in
4 ways: by button(s), by function(s), by Jog Dial command, and by
erasing all memory contents.
1. Use a ballpoint pen or other sharp point to press the MODE button
z to switch the remote controller to the LEARN mode, so that the
LEARN indicator is blinking on the LCD.
Note:
Erasing of programmed codes is only possible in the LEARN
mode.
2. Erasing by Button(s)
To erase the codes and names programmed for any button, press
and hold the CLEAR button ⁄5, then press the button to be erased
twice. This will return the button to its factory presets or leave it
empty if no factory presets are available.
Jog Dial codes may be erased in the same way, by pressing and
holding the CLEAR button ⁄5 while using the Jog Dial n to call
up the command to be erased, then pressing one of the ENT
buttons m on either side of the Jog Dial n twice. This will return
the button to its factory presets or leave it empty if no factory
presets are available.
To erase codes programmed for the CLEAR button ⁄5, simply
press the CLEAR button ⁄5 continuously for 3 seconds.
As an example, let’s clear the PLAY command from the DVD
player command set.
ON OFF ON / OFF
SOURCE
MACRO MODE
POWER
LEARNING REMOTE
CONTROL RC 7200SR
MEMO CLEAR GUIDE MUTE
ENT ENT
CH VOL OK
1 2 3 4 5
C D DVD CD-R/MD
DSS T V VCR
AMP L D TUNER TAPE
AUX
AUTO DTS CS5.1 6.1
CLEAR
ENT ENT
MEMO CLEAR GUIDE MUTE
C D DVD CD-R/MD
DSS T V VCR
AMP L D TUNER TAPE
AUX
AUTO DTS CS5.1 6.1
L D
DVD