Document Outline

• Symbol LS1203 Product Reference Guide
  • Patents
  • Warranty
  • Revision History
• Table of Contents
• About This Guide
  • Introduction
  • Configurations
  • Chapter Descriptions
  • Notational Conventions
  • Related Documents
  • Service Information
• Getting Started
  • Introduction
  • Unpacking
  • Setting Up the Scanner
    • Installing the Interface Cable
    • Removing the Interface Cable
    • Connecting Power (if required)
    • Assembling the Hands Free Stand
    • Configuring the Scanner
• Scanning
  • Introduction
  • Beeper Definitions
  • LED Definitions
  • Scanning
    • Aiming
  • Decode Zones
    • Symbol LS1203-SR Standard Range
    • Symbol LS1203-HD High Density
• Maintenance & Technical Specifications
  • Introduction
  • Maintenance
  • Troubleshooting
  • Technical Specifications
  • Scanner Signal Descriptions
• User Preferences
  • Introduction
  • Scanning Sequence Examples
  • Errors While Scanning
  • User Preferences Parameter Defaults
  • User Preferences
    • Default Parameters
    • Beeper Tone
    • Beeper Volume
    • Power Mode
    • Scanning Mode
    • Scan Line Width
    • Laser On Time
    • Beep After Good Decode
    • Transmit Code ID Character
    • Prefix/Suffix Values
    • Scan Data Transmission Format
    • FN1 Substitution Values
    • Transmit “No Read” Message
• Keyboard Wedge Interface
  • Introduction
  • Connecting a Keyboard Wedge Interface
  • Keyboard Wedge Parameter Defaults
  • Keyboard Wedge Host Parameters
    • Keyboard Wedge Host Types
    • Keyboard Wedge Country Types (Country Codes)
    • Ignore Unknown Characters
    • Keystroke Delay
    • Intra-Keystroke Delay
    • Alternate Numeric Keypad Emulation
    • Caps Lock On
    • Caps Lock Override
    • Convert Wedge Data
    • Function Key Mapping
    • FN1 Substitution
    • Send Make and Break
    • Keyboard Maps
  • ASCII Character Set for Keyboard Wedge
• RS-232 Interface
  • Introduction
  • Connecting an RS-232 Interface
  • RS-232 Parameter Defaults
  • RS-232 Host Parameters
    • RS-232 Host Types
    • Baud Rate
    • Parity
    • Stop Bit Select
    • Data Bits (ASCII Format)
    • Check Receive Errors
    • Hardware Handshaking
    • Software Handshaking
    • Host Serial Response Time-out
    • RTS Line State
    • Beep on <BEL>
    • Intercharacter Delay
    • Nixdorf Beep/LED Options
    • Ignore Unknown Characters
  • ASCII Character Set for RS-232
• USB Interface
  • Introduction
  • Connecting a USB Interface
  • USB Parameter Defaults
  • USB Host Parameters
    • USB Device Type
    • USB Country Keyboard Types (Country Codes)
    • USB Keystroke Delay
    • USB CAPS Lock Override
    • USB Ignore Unknown Characters
    • Emulate Keypad
    • USB Keyboard FN 1 Substitution
    • Function Key Mapping
    • Simulated Caps Lock
    • Convert Case
  • ASCII Character Set for USB
• Symbologies
  • Introduction
  • Scanning Sequence Examples
  • Errors While Scanning
  • Symbology Parameter Defaults
  • UPC/EAN
    • Enable/Disable UPC-A/ UPC-E
    • Enable/Disable UPC-E1
    • Enable/DisaGS1ble EAN-13/EAN-8
    • Enable/Disable Bookland EAN
    • Decode UPC/EAN/JAN Supplementals
    • User-Programmable Supplementals
    • UPC/EAN/JAN Supplemental Redundancy
    • Transmit UPC-A Check Digit
    • Transmit UPC-E Check Digit
    • Transmit UPC-E1 Check Digit
    • UPC-A Preamble
    • UPC-E Preamble
    • UPC-E1 Preamble
    • Convert UPC-E to UPC-A
    • Convert UPC-E1 to UPC-A
    • EAN-8/JAN-8 Extend
    • Bookland ISBN Format
    • UCC Coupon Extended Code
  • Code 128
    • Enable/Disable Code 128
    • Enable/Disable GS1-128 (formerly UCC/EAN-128)
    • Enable/Disable ISBT 128
  • Code 39
    • Enable/Disable Code 39
    • Enable/Disable Trioptic Code 39
    • Convert Code 39 to Code 32
    • Code 32 Prefix
    • Set Lengths for Code 39
    • Code 39 Check Digit Verification
    • Transmit Code 39 Check Digit
    • Code 39 Full ASCII Conversion
    • Code 39 Buffering (Scan & Store)
  • Code 93
    • Enable/Disable Code 93
    • Set Lengths for Code 93
  • Code 11
    • Code 11
    • Set Lengths for Code 11
    • Code 11 Check Digit Verification
    • Transmit Code 11 Check Digits
  • Interleaved 2 of 5 (ITF)
    • Enable/Disable Interleaved 2 of 5
    • Set Lengths for Interleaved 2 of 5
    • I 2 of 5 Check Digit Verification
    • Transmit I 2 of 5 Check Digit
    • Convert I 2 of 5 to EAN-13
  • Discrete 2 of 5 (DTF)
    • Enable/Disable Discrete 2 of 5
    • Set Lengths for Discrete 2 of 5
  • Chinese 2 of 5
    • Enable/Disable Chinese 2 of 5
  • Codabar (NW - 7)
    • Enable/Disable Codabar
    • Set Lengths for Codabar
    • CLSI Editing
    • NOTIS Editing
  • MSI
    • Enable/Disable MSI
    • Set Lengths for MSI
    • MSI Check Digits
    • Transmit MSI Check Digit(s)
    • MSI Check Digit Algorithm
  • GS1 DataBar (formerly RSS, Reduced Space Symbology)
    • Convert GS1 DataBar to UPC/EAN
  • Symbology - Specific Security Levels
    • Redundancy Level
    • Security Level
    • Bi-directional Redundancy
  • Symbology - Intercharacter Gap
• 123Scan
  • Introduction
  • Communication with 123Scan
  • 123Scan Parameter
• Standard Defaults
• Programming Reference
  • Symbol Code Identifiers
  • AIM Code Identifiers
• Sample Bar Codes
  • Code 39
  • UPC/EAN
    • UPC-A, 100%
    • EAN-13, 100%
  • Code 128
  • Interleaved 2 of 5
  • GS1 DataBar
    • GS1 DataBar-14
• Numeric Bar Codes
  • Numeric Bar Codes
  • Cancel
• ASCII Character Sets
• Index