Maytag 750 - Manual (Page 10)

9
Oven Cooking
Timer
The timer can be set from one minute (1:00) up to 11 hours
and 59 minutes (11:59).
The timer can be used independently of any other oven
activity. It can also be set while another oven function is
operating.
The timer does not control the oven.
To set the Timer:
1. Press the Timer pad.
• “0:00” lights in the display.
• “Timer” will flash.
2. Press the More+ or Less- pad until the
correct time appears in the display.
• “Timer” will continue to flash.
3. Press Timer pad again or wait four seconds.
• The time begins counting down.
• The last minute of the timer countdown will be displayed
as seconds.
4. At the end of the set time, three long beeps will sound.
To cancel the Timer:
1. Press and hold the Timer pad for three seconds.
OR
2. Press the Timer pad and set the time to 0:00.
Locking the Control
and Oven Doors
The touchpads and oven doors can be locked for safety,
cleaning, or to prevent unwanted use. They will not function
when locked.
If the oven is currently in use, the touchpads and doors
cannot be locked.
The current time of day will remain in the display when the
controls are locked.
To cancel the Clock display:
If you do not want the time of day to display:
Press and hold the Upper Oven CANCEL
and Clock pads for several seconds. The
time of day will disappear from the display.
When the clock display is canceled, press
the Clock pad to briefly display the time of day.
To restore the Clock display:
Press and hold the Upper Oven CANCEL and Clock pads for
several seconds. The time of day will reappear in the display.
Note: The touchpads and oven doors cannot be locked if
the oven temperature is 400° F or above.
To lock both doors:
Press and hold the Upper Oven CANCEL and
Cook & Hold pads for three seconds.
• “Lock” flashes in the display while both
oven doors lock. Once complete, “Lock”
stops flashing.
• “OFF” is displayed for 10 seconds whenever a pad is touched.
To unlock both doors:
Press and hold the Upper Oven CANCEL and Cook & Hold pads
for three seconds.
• “Lock” flashes and then disappears from the display.
• “OFF” appears in the display for several seconds while
doors are unlocking.
Fault Codes
“Bake” or “Lock” may flash rapidly in the display to alert you if
there is an error or a problem. If “Bake” or “Lock” flash in the
display, press CANCEL pad. If “Bake” or “Lock” continue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
Adjusting the Sound Level
The factory default setting for sound is medium (MEd), but it
can be changed to low (Lo) or high (HI). To change the
setting:
1. Press and hold More+ and upper oven CANCEL pads for
three seconds. A beep will sound and the current sound
level (“Lo”, “MEd” or “HI”) will appear in the display.
2. Press More+ pad to increase sound level or the Less- pad
to decrease sound level.
3. Wait four seconds and the new setting will be accepted.
4. If the More+ or Less- pad is not pressed within 30 sec-
onds, the control will return to the existing settings.
Changing Temp ° F/ ° C
The factory default setting for temperature is Fahrenheit. To
change the setting:
1. Press and hold the upper oven Bake and CANCEL pads for
three seconds. A beep will sound and the current setting
(°F or °C) will appear in the display.
2. Press the More+ or Less- pad to change the setting
between °F and °C.
3. Wait four seconds and the new setting will be accepted.