T.tone menu off set up/ 1. 2, T.tone menu off set up/ 2. 6. 3, T.tone menu off set up/ 1. 3. 4. 2 – Marantz SR5500 User Manual

Page 11

Advertising
background image

ENGLISH

8

RESETTING THE ALL CODE

1.

Press and hold down the any

Function

Selector

button and press

SETUP

button until

the indicator blinking twice.

2.

Press the code

9

-

8

-

1

.

The indicator will blink twice.
Then, RC5500SR will return to the factory
preset code.

Note:

• After this procedure, the selected function button

is set initial code and other function buttons are
set initial code too.

Once you have found and the codes for your various
appliances, you may want to write them down here.

TV

VCR

DSS

DVD

CD

TAPE

CDR

MD

SCANNING THE CODE TABLE

1.

Switch on the appliance which should be
controlled.

2.

Press and hold down the

Function Selector

button for appliance which should be
controlled and press

SETUP

button

until the

indicator blinking twice.

3.

Press the code

9

-

9

-

1

.

The indicator will blink twice.

4.

Aim the remote control at the appliance and
slowly alternate between pressing

POWER

button

and the

Function Selector

button for

the appliance.

5.

Stop when the appliance turns off.

6.

Press

SETUP

button once to lock in the code.

CHECKING THE CODE

1.

Press and hold down the

Function Selector

button for appliance which should be
controlled and press

SETUP

button until the

indicator blinking twice.

2.

Press the code

9

-

9

-

0

.

The indicator will blink twice.

3.

To view the code for first digit, press

1

once.

Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.

Note:

• If a code digit is “0”, the indicator will not blink.

4.

Repeat step 3 three more times for remaining
digits. Use

2

for the second digit,

3

for the

third digit, and

4

for the fourth digit.

PROGRAMMING THE REMOTE
CONTROLLER

The remote controller RC5500SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-
digit code or by scanning the codes until the
correct one is found. We recommend to using the
4-digit code. This mode is faster and more reliable.
The code scanning method should be used only if
y o u c a n n o t f i n d t h e c o d e f o r o n e o f y o u r
appliances. The codes are listed at the end of this
book.

Important:

• Use the remote control buttons for programming,

not the buttons of the receiver or other appliances.

• Some codes may be not match your equipment.

In this case, your equipment cannot be controlled
with this remote controller.

PROGRAMMING WITH THE 4-DIGIT CODE

1.

Press and hold down the

Function Selector

button for the appliance which should be
controlled and press

SETUP

button

until the

indicator blinks twice.

2.

Press the 4-digit code for appliance (code
table at the end of this book)

3.

When the procedure is successful, the indicator
will blink twice.

Note:

• If the indicator did not blink twice, then repeat

steps 1 through 2 and try entering the same code
again.

¤1

PURE DIRECT button

When this button is pressed, the tone control
circuit is bypassed.

¤2

SETUP / T.TONE button

(when AMP mode is selected)

Used to enter the test tone menu.

¤3

OSD button

(when AMP mode is selected)

When this button is pressed, the current setting is
displayed on the TV monitor.

¤4

SLEEP (sleep timer) button

This button is used for setting the sleep timer. It
can be operated the same way as the button on the
unit.

¤5

TV VOLUME UP ( ) /DOWN ( ) buttons

These buttons increase or decrease TV’s volume.

MENU

OSD

VOL.

TV

VOL.

MAIN

SLEEP

MUTE

AMP

AUX1

TUNER

CD

TAPE

CDR/MD

DVD

POWER

VCR1

DSS/VCR2

TV

1.

ENTER

PTY

SUB-T/ATT

AUDIO

INPUT/DISC+

F.DIRECT

RDS

TUNE/SEARCH

T-MODE

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII

EX/ES

VIRTUAL

DTS

PURE DIRECT

AUTO

3

2

1

6

5

4

9

8

0

7

T.TONE

MENU OFF

SET UP/

1.

2.

MENU

OSD

VOL.

TV

VOL.

MAIN

SLEEP

MUTE

AMP

TUNER

CD

TAPE

CDR/MD

DVD

POWER

VCR1

DSS/VCR2

TV

AUX1

2.

4.

4.

ENTER

TUNE/SEARCH

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII

EX/ES

VIRTUAL

DTS

PURE DIRECT

AUTO

3

2

1

6

5

4

9

8

0

7

T.TONE

MENU OFF

SET UP/

2.

6.

3.

MENU

OSD

VOL.

TV

VOL.

MAIN

SLEEP

MUTE

AMP

TUNER

CD

TAPE

CDR/MD

DVD

POWER

VCR1

DSS/VCR2

TV

AUX1

1.

ENTER

F.DIRECT

RDS

TUNE/SEARCH

T-MODE

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII

EX/ES

VIRTUAL

DTS

PURE DIRECT

AUTO

3

2

1

6

5

4

9

8

0

7

T.TONE

MENU OFF

SET UP/

1.
3.

4.

2.

MENU

OSD

VOL.

TV

VOL.

MAIN

SLEEP

MUTE

AMP

TUNER

CD

TAPE

CDR/MD

DVD

POWER

VCR1

DSS/VCR2

TV

AUX1

1.

ENTER

TUNE/SEARCH

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII

EX/ES

VIRTUAL

DTS

PURE DIRECT

AUTO

3

2

1

6

5

4

9

8

0

7

T.TONE

MENU OFF

SET UP/

MENU

OSD

1.

2.

04.8.2, 4:12 PM

Page 8

Advertising
This manual is related to the following products: