Impex IVT-451 User Manual
Marcy, Classic inversion table ivt-451, Model ivt-451
Advertising
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IVT-451
Retain This
Manual for
Reference
100114
OWNER'S
MANUAL
MARCY
®
CLASSIC
INVERSION TABLE
IVT-451
IMPEX
®
INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Advertising
Table of contents
Document Outline
- BEFORE YOU BEGIN...................................................................................…. 1
- IMPORTANT SAFETY NOTICES..................................................................…. 2
- HARDWARE IDENTIFIER.....…....................................................................…. 4
- ASSEMBLY INSTRUCTIONS........................................................................…. 5
- EXPLODED DIAGRAM………………………………………………………………. 11
- PARTS LIST...............................................................................................……. 12
- WARRANTY.................................................................................................…. 13
- ORDERING PARTS.......................................................................................… 13
- WARNING LABEL PLACEMENT
- ASSEMBLY INSTRUCTION
- DIAGRAM 2
- A.) Attach the Left Handle (#8) to Front Support Frame (#1). Secure it with one M8 x ¾” Allen Bolt (#35), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
- B.) Attach the Left Handle to the Rear Support Frame (#2). Secure it with one M8 x 1 ¾” Allen Bolt (#36), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
- C.) Slide one Plastic Barricade (#38) onto opening edge on the Rear Support Frame (#2) to prevent fingers from being caught in the opening.
- D.) Repeat Procedures A & B to install the Right Handle (#9).
- A.) Pull up the Foot Adjustment Lock Pin (#23). Insert the Foot Lock Frame (#13) into the Adjustment Fame (#11). Push down the Pin to securely lock the Foot Lock Frame in position.
- B.) Insert the Foot Support (#6) into the bottom of Adjustment Frame. Secure it with one M8 x 1 5/8” Allen Bolt (#40), one Ø 5/8” Washer (#46), and one M8 Aircraft Nut (#43).
- C.) Insert the Foam Tube (#10) halfway through the hole on Adjustment Frame. Push two Foam Rolls (#17) onto the Tube from both ends.
- D.) Push two Curved Foam Rolls (#16) onto the tube on Foot Lock Frame (#13) from both ends.
- A.) Pull out the Backrest Adjustment Lock Pin (#22). Insert the Adjustment Frame (#11) into the opening on the vertical frame on the back of Backrest Frame (#7). Push back the Pin into the selected hole on Adjustment Frame. The holes are scaled from 5’3” to 6’6”. User can select the hole by user’s body height for better fitment while performing the inversion exercises.
- B.) Insert the Ring Lock Pin (#21) through the hole on the vertical frame and hole on Adjustment Frame to securely lock the Adjustment Frame.
- C.) Attach hook on Inversion Adjustment Belt (#15) to Front Support Frame (#1) and to the vertical frame on Backrest Frame. Adjust the length of the Belt to adjust the extension of inversion.
- D.) Attach one side of U-shaped Lock Pin (#14) on front of Adjustment Frame, insert the other side into hole on Front Support Frame and secure with one M8 Aircraft Nut to lock Inversion Table for usage.
- E.) When using the Inversion Table, remove the side of U-shaped Lock Pin off from Adjustment Frame.
- DIAGRAM 5
- 1 Front Support Frame 1
- 14 U-shaped Lock Pin 1
- 16 Curved Foam Roll 2
- 17 Foam Roll 2
- 47 Ø ½” Washer 3