Document Outline

• Connecting the LitePro 760 is summarized on the back of this card and described in detail in the ...
• The User’s Guide contains instructions and illustrations for IBM- compatible, Macintosh, PowerBoo...
• If you are setting up the LitePro projector for the first time, install the 2 bulbs that were shi...
• 1
• Place the projector on a flat surface with the lens pointing towards the projection screen. Remov...
• 2
• Plug the “LCD” end of the LitePro cable into the “Computer” connector on the side of the projector.
• 3
• Unplug the computer’s monitor cable from the computer.
• 4
• If your computer is not an IBM- compatible, find the adapters that correspond to your computer. (...
• 5
• Plug the “Computer” end of the LitePro cable into the computer’s monitor connector.
• 6
• If you want to display the image on your monitor as well as on the projection screen, plug the “M...
• 7
• Plug the power cord into the projector, then into your electrical outlet.
• 8
• Press the “1” side of the projector’s power switch. The projector powers up and displays the Lite...
• 9
• Lift the front of the projector by the handle and release the elevator foot. When the image is at...
• 10
• Adjust the focus by turning the lens focus ring.
• 11
• If you attached your monitor in Step 7, turn on the monitor.
• 12
• Turn on the computer. The computer image should display on the projection screen.
• 13
• If your computer is ...
• Use these adapters ...
• Sun SPARCstation, SGI Indy or Indigo, Intergraph or color NeXTstation
• HP, IBM RS6000, DEC VAXstation or DECstation, Tektronix X terminal
• Apple Macintosh or PowerBook
• IBM-compatible desktop or laptop, SGI Starter, Tadpole SPARCbook
• no adapters needed
• fold and tear here
• fold and tear here
• Copyright © 1995 by In Focus Systems, Inc. Wilsonville, Oregon. All rights reserved.
  • FCC Warning
• This equipment has been tested and found to comply with the limits for a Class A digital device, ...
  • Safety Certifications
• UL, CUL, TUV
  • Instructions to User
• This equipment generates, uses and can radiate radio frequency energy and, if not installed and u...
• • Reorient the receiving antenna for the radio or television.
• • Relocate the equipment with respect to the receiver.
• • Plug the equipment into a different outlet so the equipment and receiver are on different branc...
• • Fasten cables using mounting screws to ensure adequate electromagnetic interference controls.
  • Trademarks
• All trademarks are the property of their respective owners and are used in this publication for i...
• The following are trademarks or registered trademarks of their respective companies:
• • IBM and PS/2: International Business Machines, Inc.
• • Apple, Macintosh, Mac II, LC, PowerBook, Quadra, Performa, and Power Mac: Apple Computer Corp.
• • VAXstation and DECstation: Digital Equipment, Inc.
• • IRIS, Indy and Indigo: Silicon Graphics Computer Systems
• • Sun, SPARCstation: Sun Microsystems, Inc.
• • SPARCbook: Tadpole Technology, Inc.
• • LitePro and IN FOCUS SYSTEMS: In Focus Systems, Inc.
• • UNIX: AT&T Technologies, Inc.
• Please read these instructions before using your LitePro projector. Failure to comply with these ...
• These graphics are used throughout this manual to draw your attention to important information ab...
  • Information that may be unusual or unexpected.
  • Information that helps you avoid damage to your equipment.
  • Information that helps you avoid personal injury.
• These graphics are used on the LitePro:
• Attention - Refer to the User’s Guide for important safety information.
• Fuse - Refer to “Replacing the Fuse” on page31 of this User’s Guide for important safety informa...
• Hot Surface - Do not touch until the LitePro has cooled.
• Use only a three-wire grounding type power source. The power source should not exceed 250 volts r...
• Use only the power cord that was shipped with the LitePro. Although other power cords might be si...
• The LitePro is grounded through the grounding conductor on the power cord. To avoid electric shoc...
• For protection against the risk of fire, use only a fuse of the specified type. Refer to page41 ...
• To avoid overheating and unacceptable image quality, replace the projection lamp with a lamp of t...
• The rear of the LitePro becomes very hot during operation. Avoid touching the exhaust grill on th...
• Openings in the LitePro case provide ventilation to protect it from overheating. Keep loose paper...
• Do not set drinks on top of the LitePro. Spilled liquids can flow inside and damage the LitePro.
• The only user-serviceable parts on the LitePro are inside the lamp door at the rear. Do not open ...
• Introduction 1
• Compatibility 2
• Cables and Adapters 2
• Usage Guidelines 3
• If You Need Assistance 3
• Connecting the LitePro 760 5
• Setting Up 5
• Connecting your Computer 7
• Powering Up the LitePro 15
• Turning the LitePro Off 15
• Using the LitePro 760 17
• Using the Remote Control 17
• Focusing the Image 17
• Adjusting the Height 18
• Reference to the Remote Control Buttons 19
• Using the Menu 21
• Menu Functions 22
• Switching Projection Lamps 24
• Maintenance 27
• Cleaning the Lens 27
• Replacing the Projection Lamps 28
• Replacing Batteries in the Remote Control 30
• Replacing the Fuse 31
• Troubleshooting 35
• Before You Call for Assistance 35
• Solutions to Common Problems 36
• Appendix 39
• Compatibility and Cabling 39
• Specifications 41
• Accessories 43
• Cable Connector Pin Assignments 44
• Portable and Laptop Activation Chart 46
• Index 49
• The In Focus Systems LitePro 760 LCD projector has a resolution of 1024x768 pixels and 24,389 dis...
• Shipping Box Contents
• 1.
• LitePro 760 LCD Projector
• 7.
• 13W3 Adapters
• 2.
• LitePro 760 User’s Guide
• 8.
• BNC Adapters
• 3.
• Remote Control (2)
• not shown:
• 4.
• Power Cord
• Fuses
• 5.
• LitePro Cable
• Projection Lamps
• 6.
• Mac II Adapters
• Lens Cover
• Carrying Case
• Read Me First card
  • Compatibility
• The LitePro 760 is compatible with a wide variety of computers including:
• • IBM-compatible desktop and laptop systems in VGA, SVGA, XGA and VESA modes
• • IBM PS/2 in VGA and MCGA modes.
• • most Macintosh systems, including PowerBook, Mac II, Performa, Quadra and PowerMac
• • UNIX workstations
• • X terminals
• The LitePro 760 is not compatible with these systems:
• • IBM-compatibles in CGA or EGA graphics mode
• • Macintosh 128, 512, Plus, SE, SE/30 or Classic
• • Macintosh Portable
• Refer to the Appendix for a complete list of the systems that have been tested with the LitePro 760.
  • Cables and Adapters
• The LitePro 760 comes with these cables and adapters:
• • LitePro cable, this Y-shaped cable connects the LitePro to your computer and to your monitor. I...
• • Two Macintosh adapters that attach to the “Monitor” and “Computer” ends of the LitePro cable fo...
• • Two 13W3 adapters that attach to the “Monitor” and “Computer” ends of the LitePro cable for Sun...
• • Two BNC adapters that attach to the “Monitor” and “Computer” ends of the LitePro cable for HP, ...
• • Power cable.
  • Usage Guidelines
• • The back of the LitePro can be very hot to the touch after use. Use extreme care or let it cool...
• • Do not block the grills at the back of the LitePro. Restricting the air flow through the LitePr...
• • Handle the LitePro as you would any product with glass components. Be especially careful not to...
• • Avoid leaving the LitePro in direct sunlight or extreme cold for extended periods of time. If t...
• • Transport the LitePro in the original shipping carton or approved hard case (see your In Focus ...
  • If You Need Assistance
• The first place to look for help is in this manual. Be sure to check the troubleshooting guidelin...
• If this manual does not answer your question, call your In Focus dealer. You can also call In Foc...
• Your LitePro is backed by a limited one-year warranty. The details of the warranty are printed at...
• This chapter describes how to position the LitePro for optimum viewing and how to connect it to y...
  • Setting Up
    • 1. Place the projector on a flat surface.
• • The projector must be within 6 feet of your power source.
• • The projector must be within 6 feet of the computer.
• • If you are installing the projector on the ceiling, refer to the Ceiling Mount Installation Gui...
• • For information about projector placement and image size, see the “LitePro Tips” box on the nex...
  • 2. Orient the projector so that its lens faces the projection screen.
• • If you want to use the LitePro’s Rear Project feature, set it up behind your translucent screen...
  • 3. If the projection lamps have not been installed in the projector yet, refer to “Replacing the ...
  • 4. Remove the lens cover.
  • 5. Plug the power cord into the projector, then plug it into your electrical outlet.
• • While the cord is connected, you can switch the projection lamp off by pressing the standby but...
  • Always use the power cord that was shipped with your LitePro 760. The projector accepts power fro...
    • 6. On the Y-shaped LitePro cable that was shipped with the projector, locate the end that says “L...
    • 7. Make sure your computer and monitor are turned off.
• LitePro Tips
• IMAGE SIZE
• The distance from the LitePro’s lens to the screen determines the size of the projected image as ...
  • Connecting your Computer
• To connect the projector to your computer, refer to the table below. Follow the procedure that co...
• If Your Computer is:
• You will use:
• Turn to:
• Sun SPARCstation
• two 13W3 adapters
• page8
• SGI Indy and Indigo
• two 13W3 adapters
• page8
• Intergraph 2400 or 6400 workstation
• two 13W3 adapters
• page8
• Color NeXTstation
• two 13W3 adapters
• page8
• HP workstation
• two BNC adapters
• page10
• IBM RS6000/220 or 250
• two BNC adapters
• page10
• DEC VAXstation or DECstation 3100
• two BNC adapters
• page10
• Tektronix X Terminal
• two BNC adapters
• page10
• IBM-compatible desktop computer
• no adapters
• page11
• IBM PS/2, 90/XGA or 95/XGA
• no adapters
• page11
• SGI Starter 1
• no adapters
• page11
• Macintosh desktop computer
• two Mac adapters
• page12
• IBM-compatible laptop computer
• no adapters
• page13
• Tadpole SPARCbook
• no adapters
• page13
• Macintosh PowerBook
• one Mac adapter
• page14
• Follow this procedure if your computer is a Sun SPARCstation, SGI Indigo or Indy, Intergraph 2400...
  • 1. Locate your monitor cable; it connects the monitor to the computer. Unplug it from the compute...
  • 2. Attach one of the 13W3 adapters to the “Computer” end of the LitePro cable.
• • If your computer is an SGI, plug the “SGI” end of the adapter into the “Computer” end of the Li...
  • 3. Plug the adapter (with the cable attached) into the monitor connector on the computer.
  • 4. Attach the other 13W3 adapter to the “Monitor” end of the LitePro cable.
• • If your computer is an SGI, plug the “SGI” end of the adapter into the “Monitor” end of the Lit...
  • 5. Plug the adapter (with the cable attached) into the computer’s monitor cable.
  • 6. Tighten the thumb screws on all the connectors to ensure proper grounding.
  • 7. Turn on the monitor.
  • 8. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 9. Turn on the computer.
• Follow this procedure if your computer is an HP workstation or X terminal, an IBM RS6000/220, a D...
  • 1. Locate your monitor cable; it connects the monitor to the computer. Unplug it from the compute...
  • 2. Attach one of the BNC adapters to the “Computer” end of the LitePro cable. Plug the adapter (w...
  • 3. Attach the other BNC adapter to the “Monitor” end of the LitePro cable. Plug the adapter (with...
  • 4. Tighten the thumb screws on all the connectors to ensure proper grounding.
  • 5. Turn on the monitor.
  • 6. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 7. Turn on the computer.
• Follow this procedure if your computer is an IBM-compatible desktop computer, IBM PS/2, IBM 90/XG...
  • 1. Locate your monitor cable; it connects the monitor to the computer. Unplug it from the compute...
  • 2. Attach the computer’s monitor cable to the “Monitor” end of the LitePro cable.
  • 3. Attach the “Computer” end of the LitePro cable to the monitor connector on the computer.
  • 4. Tighten the thumb screws on all the connectors to ensure proper grounding.
  • 5. Turn on the monitor.
  • 6. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 7. Turn on the computer.
• Follow this procedure if your computer is a Mac II or any Mac with a separate monitor.
  • 1. Locate your monitor cable; it connects the monitor to the computer. Unplug it from the compute...
  • 2. Attach one of the Mac adapters to the “Computer” end of the LitePro cable. Plug the adapter (w...
• • If your monitor is 13 inches or smaller, set the switch on the adapter to “LoRes”. If the monit...
  • 3. Attach the other Mac adapter to the “Monitor” end of the LitePro cable. Plug the adapter (with...
  • 4. Tighten the thumb screws on all the connectors to ensure proper grounding.
  • 5. Turn on the monitor.
  • 6. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 7. Turn on the computer.
• Follow this procedure if your computer is an IBM-compatible laptop or Tadpole SPARCBook.
  • 1. Attach the “Computer” end of the LitePro cable to the graphics connector on the computer.
  • 2. Tighten the thumb screws on the connectors to ensure proper grounding.
  • 3. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 4. Turn on the computer.
• Many laptop computers automatically turn off their monitor when another display device is connect...
• You’ll need an Apple PowerBook video-out cable to use the LitePro with a PowerBook.
  • 1. Attach the video-out cable to the PowerBook.
  • 2. Attach one of the Mac adapters to the “Computer” end of the LitePro cable. Attach the adapter ...
  • 3. Tighten the thumb screws on all connectors.
  • 4. Turn on the LitePro 760 by pressing the “1” side of the power switch. (Refer to “Powering Up t...
  • 5. Turn on the computer.
  • 6. Open the PowerBook’s Control Panel.
  • 7. Click “Mirroring”.
  • 8. Restart the PowerBook.
  • Powering Up the LitePro
• Turn on the projector by pressing the “|” side of the power switch on the side of the projector.
• • After about 5 seconds, the projector test pattern appears. (If it does not, refer to “Troublesh...
• • If the image is not projected directly on the screen, adjust the height of the elevator. Refer ...
• • You may also need to focus the projector. Turn the focus ring on the projector’s lens until the...
  • With some computers, the order in which you power up the equipment is very important. We recommen...
    • Turning the LitePro Off
• It is very important to allow the projector to cool down before turning it completely off. Turnin...
  • 1. Press the standby button on the remote.
• • The bulb turns off, but the fans remain on to cool the LCD.
  • 2. After a few minutes, when the projector has cooled, press the “O” side of the power switch to ...
• This section describes how to use the LitePro 760, including these operations.
• • If the image is not completely displayed, adjust the height of the LitePro (page18) or use the...
• • If the image is out of focus, rotate the lens to focus it (this page).
• • If the image still looks bad after you have adjusted the focus, adjust the signal synchronizati...
• • If the colors do not look right, adjust the brightness (page20) and/or the red/green/blue colo...
• • If you want to project from behind your screen, switch to Rear Project mode (page23).
• • If the bulb has burned out, switch to the spare lamp (page24). If you need to install new lamp...
• This section also provides a reference to the remote control buttons and the menu commands.
  • Using the Remote Control
• To use the remote control, point it at the projection screen or at the front of the LitePro. The ...
  • Focusing the Image
• To focus the image, rotate the projection lens until the image is clear. Rotate the lens clockwis...
  • Adjusting the Height
• Your LitePro is equipped with a self-locking, quick-release elevator foot. If the projected image...
• To raise the LitePro:
  • 1. Raise the front of the projector off the table by lifting up on the handle.
  • 2. Press the quick-release button (just inside the handle). The elevator foot releases.
  • 3. Gently lift or lower the projector to the desired height. When you release the handle, the ele...
  • 4. To more closely adjust the projector’s height, rotate the elevator foot clockwise to raise the...
• To lower the elevator foot:
• • Holding the LitePro handle, press the elevator’s quick release button. Push the elevator back u...
  • Always hold the LitePro’s handle when you press the elevator’s quick release button.
    • Reference to the Remote Control Buttons
• This section provides an alphabetical reference to the remote buttons. The names of the buttons a...
• When you press menu, the LitePro menu appears at the top of the screen. Press menu again to remov...
• When you press standby, the projector turns off its lamp to conserve electricity. The fans remain...
• The operation of the arrow buttons depends on whether or not the on-screen menu is displayed. Whe...
• When the menu is not displayed, the arrow buttons move the image in the direction of the arrow. I...
• The arrow buttons are auto-repeating; they repeat their function as long as you hold down the but...
• Adjust the contrast if the white areas of the projected image do not appear to be solid white. To...
• Both contrast buttons are auto-repeating; they continue to adjust the contrast setting as long as...
• Adjusting the brightness lightens or darkens the image. To lighten the image, press the + (plus) ...
• Adjusting the brightness changes the amounts of red, green and blue in the image. If the LitePro ...
• Both ends of the brightness button are auto-repeating; they continue to adjust the brightness set...
• Adjusting the synchronization fine tunes the LitePro to match the signals from your computer, dec...
• There are 32 sync levels. Press the sync+ or sync- buttons to cycle through the sync levels unt...
  • Using the Menu
• The LitePro 760’s on-screen menu allows you to adjust the individual colors in the projected imag...
• • language of the menu
• • number of displayable colors
• • rear projection mode
• • tracking
• • color inversion
• • reset adjustments
• Each of the menu functions is described on the following pages in “Menu Functions”.
• To display the menu:
• • Press the menu button on the remote. (The image quickly blinks off and back on when you display...
• To remove the menu from the screen:
• • Press the menu button again.
• • Use the left and right buttons to highlight a menu function.
• • Use the up and down arrow buttons to adjust or change a menu function.
• To reset all menu settings to their factory default values, select Reset. (The image quickly blin...
• The left side of the menu contains information about the state of the LitePro. If you need to cal...
• • Track The current track setting. This value changes as you adjust the Track bar. (Refer to “Tra...
• • Horiz The horizontal synchronization rate.
• • Vert The vertical synchronization rate.
• • Mode This value identifies the mode in which the LitePro is operating.
  • Menu Functions
• Follow the instructions given above in “Using the Menu” to access the menu and select the functio...
• Adjusting the Red bar changes the amount of red in the projected image. As you move the adjustmen...
• Pressing the brightness button on the remote changes the red, blue and green values.
• Adjusting the Green bar changes the amount of green in the projected image. As you move the adjus...
• Adjusting the Blue bar changes the amount of blue in the projected image. As you move the adjustm...
• The Track function adjusts the LitePro 760’s internal clock to match the signal from your compute...
• Adjusting the contrast setting affects the amount of white in the projected image. Adjust the con...
• Changes the language in which the menu is displayed. You can choose English, French, German, Span...
• When you select Rear Project, the LitePro 760 reverses the image so you can project from behind t...
• The Colors function allows you to change the number of displayable colors. You can select 8 or 24...
• When you select Inverse, the LitePro switches all the colors of the image so that their opposites...
• When you select Reset, the LitePro changes all the adjustments you made back to the factory defau...
• • position
• • brightness
• • contrast
• • sync
• • red, green and blue
• • colors
• • track
• • inverse
  • Switching Projection Lamps
• The LitePro was shipped with two projection lamps. To avoid breaking during shipping, they are no...
• When both lamps are installed in the LitePro, only one is used at a time. The other is available ...
• To switch from the active lamp to the spare lamp:
• • Gently slide the lamp changer knob to the other side of the projector as shown here.
  • When switching lamps, be careful not to touch the exhaust grill on the door. This area is very ho...
  • Do not switch the lamp changer back and forth rapidly. This can damage the lamp filaments and sho...
• This section describes:
• • how to clean the lens,
• • how to replace the projection lamps,
• • how to replace the batteries in the remote control, and
• • how to replace the fuse.
  • Do not open the LitePro case! Opening the case will expose you to electric shock hazard. Except f...
    • Cleaning the Lens
• Follow these steps to clean the projection lens.
  • 1. Apply a non-abrasive glass cleaner to a soft, dry cleaning cloth.
• • Be careful not to use excessive amounts of cleaner.
• • Abrasive cleaners, solvents or other harsh chemicals may scratch the lens.
  • 2. Lightly wipe the cleaning cloth over the lens.
  • 3. If you will not be using the LitePro immediately, replace the lens cover.
  • Replacing the Projection Lamps
• When a lamp fails, be sure to replace it with another EVD bulb (36 volt, 400 watt) from General E...
• You can order replacement lamps from In Focus. Refer to “Accessories” on page43 for information.
• Follow these steps to replace the lamps.
  • 1. Press the “0” side of the LitePro’s power switch. Then, allow the LitePro to cool thoroughly (...
  • Allow the LitePro to cool for at least 20 minutes before you attempt to open the lamp door! The i...
    • 2. While you’re waiting for the LitePro to cool, find a clean soft cloth that you can use to hold...
    • 3. Disconnect the power cord from the LitePro.
    • 4. Open the lamp door. To do this, push in on the two buttons as shown below, then lift the door up.
    • 5. Hold the lamp door open with one hand.
    • 6. Using the cloth, unplug the old bulb from its socket as shown below. Be very careful not to to...
  • Do not touch the bulbs with your bare fingers. Always hold them with their plastic bag or a clean...
    • 7. Keeping it in its plastic bag, remove one of the replacement bulbs from the box.
    • 8. Without forcing it, insert the bulb all the way into the socket. Be sure to insert the bulb st...
    • 9. Slide the lamp changer to the other side.
    • 10. Replace the other bulb if necessary. Be sure not to touch it with your bare fingers.
• • Save the box. You may need it later to pack the bulbs for shipping.
  • 11. Close the lamp door.
  • Never operate the LitePro with the lamp door open or removed. This disrupts the airflow, causing ...
• Your LitePro is equipped with a bulb life detection system called Bulb Guard. When the operating ...
  • Replacing Batteries in the Remote Control
• Follow these steps to replace the batteries.
  • 1. Turn the remote face down in your hand.
  • 2. Slide the battery cover off in the direction shown.
  • 3. Remove the old batteries.
  • 4. Install two new AAA alkaline batteries.
  • 5. Replace the battery cover.
  • Replacing the Fuse
• A power line surge or spike can blow the power supply fuse and cause the LitePro to stop working....
  • Use only the specified power supply fuse. Using a different fuse may cause serious damage to the ...
• The correct fuse for your LitePro depends on the power line voltage in the country where you are ...
• • If your line voltage is 220V to 240V (as in most European countries), use a 6.3 amp, 250V, 5x20...
• • If your line voltage is 100V to 120V (as in Japan, the United States and most North American co...
• Follow these steps to replace the fuse.
  • 1. Make sure that the condition that caused the fuse to blow no longer exists.
  • 2. Turn off the LitePro by pressing the “O” side of the power switch on the side of the LitePro.
  • 3. Unplug the power cord from the LitePro.
  • 4. Locate the fuse holder on the side of the LitePro between the power switch and the power cord ...
  • 5. Using a small coin or a flat blade screwdriver, turn the fuse holder a quarter turn in the clo...
  • 6. Pull the fuse holder out of the LitePro.
  • 7. Remove the blown fuse from the fuse holder.
  • 8. Push the new fuse into the clips of the holder until it is securely seated.
  • 9. Place the fuse holder back in the LitePro.
  • 10. Using the same tool you used in step 5, turn the fuse holder a quarter turn counter-clockwise.
  • 11. Plug the power cord back in.
  • 12. Press the “|” side of the power switch to turn the LitePro back on.
  • Do not open the LitePro case! Opening the case may cause electric shock! Except for the projectio...
    • Before You Call for Assistance
• Before calling your dealer for assistance, follow these steps in this order to make sure everythi...
  • 1. Make sure you connected the LitePro to you equipment as described in “Connecting the LitePro 7...
  • 2. Check cable connections. Verify that all computer and power cables are properly connected.
  • 3. Verify that all power is switched on.
  • 4. Verify that you have pushed the On/Off button on the remote.
  • 5. If the LitePro still does not display an image, reboot the computer. (Macintosh computers requ...
  • 6. If the image is still bad, unplug the LitePro from the computer and check the computer monitor...
  • 7. If the problem still exists, read through the problems and solutions in this chapter.
• If you call In Focus for assistance:
• • Display the menu (press the menu button on the remote). Write down the information that is disp...
• • Find out what kind of graphics controller card is installed in your computer. (This is the circ...
  • Solutions to Common Problems
    • Problem: Nothing on screen
• • Is the projector switched on? The “|” side of the power switch should be pressed. Refer to the ...
• • Is the LitePro properly plugged into a live AC outlet?
• • If your Lite Pro is plugged into a power strip, is the power strip turned on?
• • Is the lens cap still on the projection lens at the front of the projector?
• • Are the lamps installed? Refer to “Replacing the Projection Lamps” on page28 or the Read Me Fi...
• • Is the bulb burned out? If the bulb is burned out, you can switch to the spare. Refer to “Switc...
• • Has the projector’s fuse blown? Refer to “Replacing the Fuse” on page31 for more information.
• • Is the LitePro adjusted properly? Adjust the brightness. Refer to “brightness” on page20 for m...
• • Does the cable have bent pins in any of the connectors? Check the pins on all three ends of the...
  • Problem: Color or VGA text not being projected
• • The brightness control may need to be adjusted. Adjust the brightness up or down until the text...
  • Problem: Image is not centered on the screen
• • Use the arrow buttons on the remote to center the image. (The menu must be off when you re-posi...
  • Problem: Only the test pattern is displayed
• • Are your cables connected correctly? Check to see that the cable is connected to the graphics p...
• • Did you turn on the equipment in the correct order? You may need to repeat the power up sequenc...
• • Is your computer graphics system set up correctly? Check the following:
• - Is your computer’s graphics board turned on?
• - If your computer has an external video board, is it turned on?
• - Does your computer have a compatible graphics board? The LitePro 760 is not compatible with CGA...
  • Problem: Image is too wide or narrow for screen
• • You may need to adjust the tracking to reduce or enlarge the projected image. Refer to “Track” ...
  • Problem: Image is out of focus
• • Turn the projection lens to focus the image.
• • The projection screen must be at least 4 feet (1.2m) from the LitePro.
• • The projection lens may need cleaning.
  • Problem: Image and menus are reversed left to right
• • Rear projection mode is probably set. To switch back to forward projection:
• 1. Press the menu button on the remote to display the menu.
• 2. Select “Rear Projection”. Press the up or down button to switch back to forward projection.
• 3. Press menu again to remove the menu.
  • Problem: LitePro displays vertical lines, “bleeding” or spots
• • Adjust the contrast. Refer to “contrast” on page20 for more information.
• • The projection lens may need cleaning.
  • Problem: Image is “noisy” or streaked
• • Adjust the contrast. Refer to “contrast” on page20 and page23 for more information.
• • Adjust the Sync. Refer to “sync” on page20 for more information.
  • Problem: Projected colors don’t match the monitor’s colors
• • Adjust the brightness and/or contrast. Remember that, just as there are differences in the disp...
  • Problem: “EEPROM Failed” displays on the menu
• • One of the integrated circuits inside the LitePro has failed. The only functionality that is lo...
  • Problem: Remote not operating correctly
• • You may need to replace the batteries in the remote. Refer to “Replacing Batteries in the Remot...
  • Compatibility and Cabling
• The following table lists the computers that the LitePro 760 was compatible with when this manual...
• System
• Resolution
• Adapter
• IBM VGA 256 colors
• 640x400
• none
• IBM VGA graphics
• 640x480
• none
• IBM text
• 720x480
• none
• Super VGA extended
• 800x600
• none
• Super VGA high resolution, interlaced and non-interlaced
• 1024x768
• none
• 132 column text
• 1056 chars. wide
• none
• IBM XGA and 8514, interlaced
• 1024x768
• none1
• IBM RS6000 Model 220, with Gt1 adapter with 8515
• 1024x768
• none
• IBM RS6000 Model 220, with Gt1 adapter with 6091
• 1024x768
• BNC
• Intergraph
• 1184x884
• 13W3
• SGI Indigo
• 1024x768
• 13W3
• SGI Indy
• 1024x768
• 13W3
• Sun SPARCstation
• 1024x768
• 13W3
• 1152x9002
• 13W3
• Digital Equipment Corporation (DEC)
• 1024x864
• BNC
• NeXTstation color
• 1120x8322
• 13W3
• NeXTstation monochrome
• 1120x8322
• 13W33
• Hewlett Packard 710 Series 16”
• 1024x768
• BNC
• Hewlett Packard 16” X terminal
• 1024x768
• BNC
• Apple Macintosh
• 640x480
• Mac
• Mac with SuperMac 16” color monitor
• 832x624
• Mac
• Mac with SuperMac 19” color monitor
• 1024x768
• Mac
• Mac with SuperMac 19” or 20” dual mode monitor
• 1024x768 or 1152x8702
• Mac
• Mac with SuperMac 21” two-page monitor
• 1152x8702
• Mac
• Mac with Radius 21” Actual Size monitor
• 1056x8072
• Mac
• Mac with Radius Precision Color/20 Two-Page monitor
• 1152x8702
• Mac
• Mac with Radius Precision Color/20 Actual Size monitor
• 1024x768
• Mac
• Mac with Radius Precision Color/20 16” mode monitor
• 832x624
• Mac
• Mac with Radius Precision Color/19 Actual Size monitor
• 1024x768
• Mac
• Mac with RasterOps 21” color monitor
• 1152x8702
• Mac
• Mac with RasterOps 19” color monitor
• 1024x768
• Mac
• Mac with RasterOps Dual Scan monitor
• 1024x768
• Mac
• 1152x8702
• Mac
• Mac with RasterOps 16” color monitor
• 832x624
• Mac
• Mac with E-Machines monitor, modes 1 - 8
• 640x480 to 1152x8702
• Mac
• Mac with Apple 16” color monitor
• 832x624
• Mac
• Mac with Apple 21” color monitor
• 1152x8702
• Mac
• Lapis LC 21
• 1024x768
• BNC
• 1 Use the XGA terminator if you do not connect your monitor. Call In Focus Technical Support for ...
• 2 The LitePro 760 displays only a 1024x768 image; some of the higher resolution image will be cut...
• 3 This connection requires a monochrome-to-RGB converter box from Extron.
  • Specifications
• Projection Lamps
• Type
• 400 watt tungsten halogen, ANSI EVD type bulbs - manufactured by OSRAM, part number HLX 64663
• Life
• Average 50 hours each
• Fuse
• 100 to 120V nominal line
• 10A, 250V, 3AB
• 220 to 240V nominal line
• 6.3A, 250V, 5x20mm
• Input Power Requirements
• 100 to 240 VAC, 7.2A to 2500 mA, 50 to 60 Hz.
• Remote Control
• Battery
• Two (2) AAA alkaline cells
• Range
• 25 feet (7.62m) when reflected off a white wall or projection screen within 45˚ of the projection...
• Optical
• Brightness
• minimum 150 lumens (measured by ANSI 12 point method)
• Uniformity
• 2:1 maximum (measured by 12 point method)
• Projection Range
• 5 to 15 feet (1.5 to 4.6 m)
• Temperature
• Operating
• 15˚ to 32˚C
• Non-operating
• -20˚ to 60˚C
• Altitude
• Operating
• 0 to 10,000 feet (3048 meters)
• Non-operating
• 20,000 feet (6096 meters)
• Humidity
• Operating and non-operating
• 10 to 90% RH, non-condensing
• Dimensions
• LitePro 760
• 20 x 11.5 x 8 inches
• (51 x 29 x 20 cm)
• Weight
• Unpacked
• 19.5 lbs. (8.8 kg)
• As shipped
• 28 lbs (12.7 kg)
  • Accessories
• Contact your In Focus dealer to order. Refer to the In Focus Accessories Catalog for additional i...
• Standard Accessories (ship with LitePro)
• Part Number
• Read Me First card
• 009-0192-xx
• LitePro 760 User’s Guide
• 010-0086-xx
• Soft Carry Case
• 110-0079-xx
• Shipping Box
• 110-0080-xx
• LitePro Cable (VGA cable)
• 210-0041-xx
• Projection Lamp, 36V, 400W
• 232-0020-xx
• Mac Adapters (set of 2)
• 516-0005-xx
• BNC Adapters (2)
• 515-0028-xx and 515-0029-xx
• 13W3 Adapters (2)
• 515-0030-xx and 515-0031-xx
• Lens Cap
• 340-0148-xx
• Remote Control
• 590-0142-xx
• Power Cords (one ships with LitePro, depends on country)
• North American Power Cord
• 210-0023-xx
• Australian Power Cord
• 210-0027-xx
• UK Power Cord
• 210-0028-xx
• European Power Cord
• 210-0029-xx
• Danish Power Cord
• 210-0030-xx
• Swiss Power Cord
• 210-0031-xx
• Fuses and Fuse Holders (one set ships with LitePro, depends on country)
• Fuse, 10A, 3AB (use w/110V)
• 749-0013-xx
• Fuse Holder for 10A, 3AB Fuse (use w/110V)
• 749-0014-xx
• Fuse, 6.3A, 5x20mm (use w/220V)
• 749-0010-xx
• Fuse Holder for 6.3A, 5x20mm Fuse (use w/220V)
• 749-0011-xx
• Compatible Product
• LitePro Ceiling Mount Kit
• 591-0098-xx
  • Cable Connector Pin Assignments
• The Y-shaped LitePro cable that shipped with your LitePro has three connectors, they are labeled ...
• The end of the LitePro cable that plugs into the LitePro itself is a male 26-pin D-style connecto...
• Input Pin
• Signal Description
• Output Pin
• 1
• Vertical sync
• 10
• 2
• Horizontal sync
• 11
• 8
• Blue analog
• 14
• 6
• reserved
• 12
• 7
• reserved
• 13
• 9
• Red analog
• 15
• 16
• reserved
• 3
• 17
• reserved
• 4
• 18
• Green analog
• 5
• 20
• GND
• 21
• GND
• 22
• GND
• 23
• Digital/analog video cable ID
• 24
• GND
• 25
• VGA/no video cable ID pin
• 26
• Monochrome digital (Hercules)
• 19
• The pin assignments are the same for the “Monitor” and “Computer” connectors. The “Monitor” conne...
• Pin
• Signal Description
• 1
• Red analog input
• 2
• Green analog input with composite sync
• 3
• Blue analog input
• 4
• GND
• 5
• GND
• 6
• Red GND
• 7
• Green GND
• 8
• Blue GND
• 9
• NC
• 10
• Sync GND
• 11
• GND
• 12
• NC
• 13
• Horizontal sync/composite sync input
• 14
• Vertical sync input
• 15
• NC
  • Portable and Laptop Activation Chart
• Most laptop computers de-activate their built-in monitors when a second display device is connect...
• Computer
• Key command to activate port
• Key command to de-activate port
• Acer
• Ctrl-Alt-Esc (for setup)<
• Ctrl-Alt-Esc (for setup)
• AST
• FN-D or Ctrl-D
• FN-D or Ctrl-D
• Ctrl-FN-D
• Ctrl-FN-D
• FN-F5
• FN-F5
• type from A:/IVGA/CRT
• type from A:/IVGA/CRT
• Austin
• Ctrl-Alt-,,
• Ctrl-Alt-,
• Altima*
• Shift-Ctrl-Alt-C
• Shift-Ctrl-Alt-L
• setup VGA/Conf.Simulscan
• setup VGA/Conf.Simulscan
• Amrel* **
• setup menu
• setup menu
• Shift-Ctrl-D
• Shift-Ctrl-D
• Apple
• see Mac Portable and Mac PowerBook
• BCC
• automatic - no activation command needed
• reboot computer
• Bondwell
• LCD or CRT option
• LCD or CRT option
• Chaplet**
• setup screen
• setup screen
• Commax
• Ctrl-Alt-#6
• Ctrl-Alt-#5
• Compaq**
• Ctrl-Alt-<
• Ctrl-Alt->
• FN-F4
• FN-F4
• Data General
• Ctrl-Alt-Command
• Ctrl-Alt-Command
• Data General Walkabout
• 2 CRT/X at DOS prompt
• reboot
• Datavue
• Ctrl-Shift-M
• Ctrl-Shift-M
• Dell*
• Ctrl-Alt-<
• Ctrl-Alt->
• Ctrl-Alt-F10
• Ctrl-Alt-F10
• Digital
• automatic
• reboot
• FN-F2
• FN-F2
• Dolch
• dip switch to CRT
• dip switch to LCD
• Epson
• dip switch to CRT
• dip switch to LCD
• Everex**
• setup screen option
• setup screen option
• For-A
• Ctrl-Alt-Shift-C
• Ctrl-Shift-Alt-L
• Gateway 2000
• FN-F1
• FN-F1
• Grid* **
• FN-F2, choose auto or simultaneous
• FN-F2
• Ctrl-Alt-Tab
• Ctrl-Alt-Tab
• Hyundai
• setup screen option
• setup screen option
• IBM 970
• automatic
• warm reboot
• IBM ThinkPad
• setup screen option
• setup screen option
• Kris Tech**
• FN-F8
• FN-F8
• Mac Portable
• no video port: not compatible
• Mac PowerBook
• 140, 145, 170
• no video port: requires a 3rd-party interface
• 160, 165, 180, 250
• automatic: use Set Mirroring option
• warm reboot
• 230
• requires Apple Docking Station
• Mastersport
• FN-F2
• FN-F1
• Micro Express
• automatic
• warm reboot
• Microslave
• automatic
• warm reboot
• Mitsubishi
• SW2 On-Off-Off-Off
• SW2 Off-On-On-On
• NCR
• setup screen option
• setup screen option
• NEC*
• setup screen option
• setup screen option
• CRT at the DOS prompt
• LCD at the DOS prompt
• Packard Bell*
• FN-F2
• FN-F2
• Ctrl-Alt-<
• Ctrl-Alt->
• Panasonic
• FN-F2
• FN-F2
• Samsung
• setup screen option
• setup screen option
• Sanyo
• setup screen option
• setup screen option
• Sharp
• dip switch to CRT
• dip switch to LCD
• SPARC-Dataview
• Ctrl-Shift-M
• Ctrl-Shift-M
• Tandy* **
• Ctrl-Alt-Insert
• Ctrl-Alt-Insert
• setup screen option
• setup screen option
• Texas Instruments
• setup screen option
• setup screen option
• Top-Link* **
• setup screen option
• setup screen option
• FN-F6
• FN-F6
• Toshiba* **
• Ctrl-Alt-End
• Ctrl-Alt-Home
• FN-End
• FN-Home
• 4500
• FN-F5
• FN-F5
• setup screen option
• setup screen option
• Wyse
• software driver
• software driver
• Zenith
• FN-F10
• FN-F10
• * These manufacturers have other models that automatically send video to the external CRT port wh...
• ** These manufacturers offer more than one key command depending on the computer model.
  • Numerics
• 13W3 adapters 1, 2, 8
  • A
• accessories 43
• activation commands for laptop computers 46
• adapters
• 13W3 1, 2, 8
• BNC 1, 2, 10
• for specific computers 2, 7, 39
• Macintosh 1, 2, 12, 14
• ordering spares 43
• shipped with panel 2
• shipped with projector 2
• air movement inside unit 3
• altitude limits 42
• Apple, see Macintosh
• arrow buttons
• re-positioning image 19
• using in menu 19, 21
• assistance, see Technical Support
  • B
• batteries, replacing in remote control 30
• blue adjustment 22
• BNC adapters 1, 2, 10
• brightness button 20, 22
• brightness, adjusting 20
• Bulb Guard 30
• bulb, see lamp
  • C
• cables
• connecting to LitePro 6
• for specific computers 39
• LitePro cable 2, 6
• monitor 8, 10, 11, 12
• pin assignments for LitePro cable 44, 45
• power cable 2, 5
• shipped with projector 2
• CGA graphics 2
• colors
• adjusting red, green or blue 22
• don’t match monitor colors 38
• inverting 23
• maximum number available 1, 23
• not displayed 36
• selecting number of 23
• Colors menu function 23
• compatibility 2, 39
• "Computer" end of LitePro cable 8, 10, 11, 12, 13, 14
• computers
• compatible with LitePro 2, 39
• connecting to LitePro 7
• contrast button 20
  • D
• DEC workstation
• adapters 2
• compatibility 39
• connecting 10
• defaults, resetting 21
  • E
• EGA graphics 2
• "EEPROM failed" displayed 38
  • F
• focusing the image 17
• fuse
• ordering spares 43
• replacing in LitePro 31
• specifications 41
• fuzzy lines displayed 23
  • G
• green adjustment 22
  • H
• height of LitePro 18
• HP workstation
• adapters 2
• compatibility 39
• connecting 10
• humidity limits 42
  • I
• IBM workstation
• adapters 10
• compatibility 39
• connecting 10
• IBM-compatible personal computers
• compatibility 2, 39
• desktop, connecting 11
• laptop, connecting 13
• image
• blinks 21, 30
• colors don’t match monitor’s colors 38
• flashes off and on 30
• focusing 17
• fuzzy lines 23
• has lines or spots 38
• not centered 37
• not displayed 36
• out of focus 17, 37
• re-positioning 19
• reversed 38
• streaked 38
• too wide or too narrow 37
• Indigo workstation (SGI)
• adapters 8
• connecting 8
• Indy workstation (SGI)
• adapters 8
• connecting 8
• Intergraph workstation
• adapters 8
• compatibility 39
• connecting 8
• Inverse menu function 23
• inverting image colors 23
  • L
• lamp
• average life 24, 41
• BulbGuard 30
• flashing off and on 30
• handling 29
• life detection system 30
• ordering spares 43
• replacing the lamps 28
• specifications 41
• switching to the spare 24
• Language menu function 23
• language, selecting for menus 23
• laptop computers
• activation sequence to allow secondary display 13, 46
• compatibility 2
• connecting to LitePro 13, 14
• LCD, description 1
• "LCD" end of LitePro cable 6
• LitePro
• accessories 43
• adjusting the height 18
• connecting to computer 6
• displaying menu 19
• not working 36
• operating limits 42
• positioning 5
• replacing batteries in the remote 30
• replacing fuse 31
• replacing lamps 28
• specifications 41
• switching to the spare bulb 24
• turning off lamp 19
• LitePro cable
• "Computer" end 8, 10, 11, 12, 13, 14
• "LCD" end 6
• "Monitor" end 8, 10, 11, 12
• connecting to LitePro 6
• description 2
• ordering spares 43
• pin assignments 44, 45
  • M
• Macintosh
• adapters 1, 2, 12, 14
• Classic 2
• compatibility 2, 39
• connecting to LitePro 12
• Performa 2
• PowerBook 2, 14
• PowerMac 2
• Quadra 2
• video-out cable 14
• MCGA graphics 2
• menu
• adjusting functions 21
• change language of 23
• description of functions 22
• displaying 19, 21
• removing 19
• selecting functions 21
• menu button 19
• monitor
• cable 8, 10, 11, 12
• connecting to LitePro 8, 10, 11, 12
• projected colors don’t match 38
• monitor activation, IBM-compatible laptop 13
• "Monitor" end of LitePro cable 8, 10, 11, 12
  • N
• NeXT workstation
• adapters 2
• compatibility 39
• connecting 8
  • O
• optical specifications 41
  • P
• PC, see IBM-compatible personal computers
• Performa, see Macintosh
• pin assignments for LitePro cable 44, 45
• power cable
• connecting to LitePro 5
• ordering spares 43
• power supply specifications 41
• PowerBook, see Macintosh
• PowerMac, see Macintosh
• project from behind the screen 23
  • Q
• Quadra, see Macintosh
  • R
• raise the LitePro 18
• Rear Projection menu function 23
• red adjustment 22
• remote control
• description of buttons 19
• not working 38
• ordering spares 43
• range 17
• replacing batteries 30
• specifications 41
• using to display menu 21
• using to turn bulb on and off 15, 19
• resetting menu adjustments 21
  • S
• SGI workstation
• adapters 2
• compatibility 39
• connecting a Starter 1 11
• connecting a workstation 8
• shipping contents 1
• signal synchronization 20
• SPARCbook, connecting 13
• spare lamp 24
• specifications 41
• standby button 19
• Starter 1 (SGI), connecting 11
• Sun workstation
• adapters 2
• compatibility 39
• connecting 8
• sync button 20
  • T
• Tadpole SPARCbook, connecting 13
• Technical Support
• diagnostic information 22
• in Europe 3
• in USA 3
• information to have on hand before you call 36
• things to try before you call 35
• Tektronix X terminal
• adapters 2
• connecting 10
• temperature limits 41
• test pattern, won’t go away 37
• text not visible 36
• Track menu function 23
• tracking
• adjusting 23
• current setting 22
• troubleshooting 35
  • U
• UNIX workstations, compatibility 2, 39
  • V
• vertical lines displayed 23, 38
• VGA graphics 2
• video (monitor) activation, IBM-compatible laptop 13
• video-out cable, for PowerBook 14
  • X
• X terminals, compatibility 2
  • LIMITED WARRANTY
• In Focus Systems Inc. (“In Focus”) warrants that each LitePro 760 (“the Product”) sold hereunder ...
  • WARRANTY LIMITATION AND EXCLUSION
• In Focus shall have no further obligation under the foregoing limited warranty if the Product has...
  • DISCLAIMER OR UNSTATED WARRANTIES
• THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES...
  • LIMITATION OF LIABILITY
• IT IS UNDERSTOOD AND AGREED THAT IN FOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY WARR...
• Part Number 010-0086-00