IBM 4690 - Manual (Page 29)

E025 – Logical unit not ready, manual intervention
required.
E026 – Logical unit not ready, format in progress.
E027 – Logical unit not ready, operation in progress.
E028 – Logical unit does not respond to selection.
E029 – Multiple peripheral devices selected.
E030 – Logical unit communication failure.
E031 – Logical unit communication time-out.
E032 – Logical unit communication parity error.
E033 – Logical unit communication CRC error
(Ultra-DMA/32).
E034 – Track following error.
E035 – Head select fault.
E036 – Error log overflow.
E040 – Write error.
E041 – Compression check miscompare error.
E042 – Data expansion occurred during
compression.
E043 – Block not compressible.
E044 – Unrecovered read error.
E045 – Read retries exhausted.
E046 – Error too long to correct.
E047 – Multiple read errors.
E048 – Incomplete block read.
E049 – No gap found.
E050 – Miscorrected error.
E051 – Decompression CRC error.
E052 – Cannot decompress using declared
algorithm.
E053 – Block sequence error.
E054 – Random positioning error.
E055 – Mechanical positioning error.
E056 – Positioning error detected by read of
medium.
E057 – Defect list error.
E058 – Parameter list length error.
E059 – Synchronous data transfer error.
E060 – Invalid command operation code.
E061 – Logical block address out of range.
E062 – Invalid element address.
E063 – Invalid field in CDB.
E064 – Logical unit not supported.
E065 – Invalid field in parameter list.
E066 – Parameter not supported.
E067 – Parameter value invalid.
E068 – Threshold parameters not supported.
E069 – Invalid release of active persistent
reservation.
E070 – Write protected.
E071 – Hardware write protected.
E072 – Logical unit software write protected.
E073 – Associated write protect.
E074 – Persistent write protect.
E075 – Permanent write protect.
E076 – Not ready to ready change, medium may
have changed.
E077 – Import or export element accessed.
E078 – Power on, reset, or bus device reset occurred.
E079 – Power on occurred.
E080 – SCSI bus reset occurred.
E081 – Bus device reset function occurred.
E082 – Device internal reset.
E083 – Parameters changed.
E084 – Mode parameters changed.
E085 – Log parameters changed.
E086 – Reservations preempted.
E087 – Copy cannot execute because Store
Controller cannot disconnect.
E088 – Command sequence error.
E089 – Overwrite error on update in place.
E090 – Commands cleared by another initiator.
E091 – Incompatible medium installed.
E092 – Cannot read medium - unknown format.
E093 – Cannot read medium - incompatible format.
E094 – Cleaning cartridge installed.
E095 – Cannot write medium - unknown format.
E096 – Cannot write medium - incompatible format.
E097 – Cannot format medium - incompatible
medium.
E098 – Cleaning failure.
E099 – Medium format corrupted.
E100 – Tape length error.
E101 – Enclosure failure.
E102 – Enclosure services failure.
E103 – Unsupported enclosure function.
E104 – Enclosure services unavailable.
E105 – Enclosure services transfer failure.
E106 – Enclosure services transfer refused.
E107 – Rounded parameter.
E108 – Saving parameters not supported.
E109 – Sequential positioning error.
E110 – Tape position error at beginning-of-medium.
E111 – Tape position error at end-of-medium.
E112 – Reposition error.
E113 – Position past beginning of medium.
E114 – Medium destination element full.
E115 – Medium source element empty.
E116 – Medium magazine not accessible.
Chapter 3. Using the Tape Drive 15