IBM 4690 - Manual (Page 30)

E117 – Medium magazine locked.
E118 – Invalid bits in identify message.
E119 – Logical unit has not self-configured yet.
E120 – Target operating conditions have changed.
E121 – Microcode has been changed.
E122 – Changed operating definition.
E123 – Inquiry data has changed.
E124 – Diagnostic failure.
E125 – Message error.
E126 – Internal target failure.
E127 – Select or reselect failure.
E128 – Unsuccessful soft reset.
E129 – SCSI parity error.
E130 – Initiator detected error message received.
E131 – Invalid message error.
E132 – Command phase error.
E133 – Data phase error.
E134 – Logical unit failed self-configuration.
E135 – Tagged overlapped commands.
E136 – Overlapped commands attempted.
E137 – Write append error.
E138 – Write append position error.
E139 – Position error related to timing.
E140 – Erase failure.
E141 – Cartridge fault.
E142 – Media load or eject failed.
E143 – Unload tape failure.
E144 – Medium removal prevented.
E145 – Operator request or state change input.
E146 – Operator medium removal request.
E147 – Operator selected write protect.
E148 – Operator selected write permit.
E149 – Log exception.
E150 – Threshold condition met.
E151 – Log counter at maximum.
E152 – Log list codes exhausted.
E154 – Voltage fault.
E155 – Decompression exception short algorithm ID.
E156 – Decompression exception long algorithm ID.
E157 – Unexpected sense data.
E158 – A Device malfunction prevents return of the
sense data.
E159 – Store Controller is not an ISA bus machine.
E160 – Illegal Length Indicator.
E161 – Illegal command.
E162 – Store Controller does not support ABIOS.
E163 – ABIOS has used all available logical IDs and
cannot allocate a logical ID for the tape drive.
E164 – The tape drive has multiple LUNs. The tape
software only supports tape drives with one LUN.
E165 – The ABIOS is using logical data pointers.
Logical data pointers are not supported.
E166 – Device is not a Tape Streamer.
E167 – Device does not support removable media.
E168 – Tape Drive does not support Accelerated
DRQ.
E169 – Packet size is not 12 bytes.
E170 – Device is not an ATAPI device.
E171 – Page code is incorrect.
E172 – Page length is incorrect.
E173 – Page support does not support the necessary
pages.
E174 – No format and partition recognition.
E175 – No fixed data partitions.
E176 – Tape drive command timed out.
User Response: Choose one of the following based on
the event (Exxx) that is displayed:
E019, E020, E021, E036, E040, E041, E042, E043,
E044, E045, E046, E047, E048, E049, E050, E051,
E052, E053, E109, E110, E111, E112, E113, E137, E138,
E140, E141, E149, E150, E151, E152
– These errors
normally indicate a tape cartridge problem. Remove
the cartridge and examine the tape. Look for any
visible damage. Retension the tape and try again. If
the problem persists, replace the tape cartridge. If
the error still persists, contact your IBM Service
representative.
E022, E023, E027, E076, E083, E084, E085, E119,
E120, E121, E122, E123, E145, E146, E148
– These
errors normally indicate a temporary condition that
will clear itself. Wait for the tape motion to stop
before attempting the operation again.
E024 – Reboot the Store Controller.
E025 – Insert the tape cartridge in the tape drive.
E026 – This error normally indicates a user problem
caused by attempting another command to the tape
drive before a format completes. Wait for format to
complete.
E028, E030, E031, E032, E033 – These errors
normally indicate a tape drive hardware problem.
Check connections to the tape drive. If the error still
persists, contact your IBM Service representative.
E029 – Make sure there is only one tape drive
installed.
E034, E091, E092, E093, E094, E095, E096, E097,
E098, E099, E100, E166, E167, E168, E169, E170,
E173, E174, E175
– These errors normally indicate an
attempt to use a tape drive that is not supported.
Make sure that the tape is a TR-4 tape. If the
problem persists, replace the tape cartridge. If the
error still persists, contact your IBM Service
representative.
16 TR-4 Tape Drive User’s Guide