Ikelite ZR950 User Manual
Page 2
BBAATTTTEERRYY AAN
ND
D TTAAPPEE
_________________________________________________________
• Install a fully charged Canon battery on the camera:
Canon NB-2LH, BP-2L13
• Other brand batteries may not fit inside the housing.
• Make sure you have loaded an appropriate digital cassette tape in the camera.
FFIIN
NAALL PPRREEPPAARRAATTIIO
ON
N
________________________________________________________
The program selector on the camera M
MU
USSTT be in the PP position for the focus lock
button to function.
The camera s auto focus feature is utilized underwater. For best results, move
in close to your subject and use the wide angle range to shoot thru as little water as
possible. The full zoom range is accessible underwater. Chart shows recommended
initial settings underwater.
W
WH
HIITTEE BBAALLAAN
NCCEE
____________________________________________________________
Initially set the white balance to Auto. Use the touch screen controls on the
housing to change white balance.
CCoolloorr FFiilltteerr:: When using the color filter during the day , set camera white balance
to Indoor for 0-15 foot depth. For 15-80 foot depth, set white balance to Outdoor.
VViiddeeoo--LLiittee:: When using optional Video Lite at NIGHT, set the camera white balance
to the Indoor position. During the DAY, use the Outdoor setting for subjects beyond
4-5 feet and the Indoor setting for closer subjects.
CCAAM
MEERRAA
SSEETTTTIIN
NGG
Power On/Off
Camera On
Zoom Lever
Wide Angle Setting
Focus
Auto Mode
Exposure
Auto Mode
Lens Cover Switch
Open
I
I N
N SS TT AA LL LL AA TT II O
O N
N
CCAAM
MEERRAA TTRRAAYY
_________________
The camera mounts to the tray,
which extends from the back plate of the
housing. D
DO
O N
NO
OTT remove the tray from
the back plate.
Position the camera against the two
stabilizing pins on the tray and secure
camera with the tripod mounting bolt.
The camera should fit easily on the tray
and should be parallel with the sides
of the tray.
IIN
NSSEERRTTIIN
NGG TTH
HEE CCAAM
MEERRAA
___________
Check that the o ring is clean and
properly positioned on the lip of the clear housing back plate.
Once the camera is mounted to the tray as shown above, pull the housing
controls out to provide clearance for installing the camera. Slowly slide the camera
tray with camera mounted back into the housing. As the camera slides into the
housing, make sure the camera lens fits into the port recess in the front of the
housing.
D
DO
O N
NO
OTT force this installation; the camera and tray should slide easily into
place so the housings back plate o ring is resting against the main housing body.
In this position the lid snaps can be positioned over the lid hooks on the housing
back plate and snapped into position to seal the housing.
H
HO
OU
USSIIN
NGG CCO
ON
NTTRRO
OLLSS
________________________________________________________
Slide the housing controls back in place making sure they properly align with the
camera functions.
Operate each control to see how it works with the camera. Some controls such as
start/stop will be used frequently. Other controls may seldom be utilized. Refer to
your camera owner s manual for the proper function of each camera control. Look
thru the back to be sure that you can see into the viewfinder.
When using the housing controls, especially the start/stop, do NOT use excessive
force because you could damage the camera.
CCAAU
UTTIIO
ON
N
Remove the lens cap and cord from the camera.
Otherwise, the cord may interfere with the housing seal.
If the housing controls are not properly positioned,
they could interfere with the housing seal.
IIKKEELLIITTEE U
UN
ND
DEERRW
WAATTEERR SSYYSSTTEEM
MSS
50 West 33rd Street • PO Box 88100 • Indianapolis, IN 46208 USA
317.923.4523
Email: [email protected]
•
www.ikelite.com
6047-01-0708
Camera Mounting Bolt
Camera Tray
O’ring
SuperEye
Back Plate
Stabilizing
Pins