Inner Space Systems CONCEPT 4000 - Manual (Page 12)

Concept 4000 / Insight - Integrated Security Management
12
Access Control
Intelligent Four Door Access Module
The Intelligent 4 Door Access module is a four door, four
reader access control module and has been specifically
designed to meet the highest levels of system integrity and
redundancy planning. The Intelligent 4 Door Access module
effectively combines offline stand-alone operation with
enhanced feature design.
The four door intelligent access module fully supports the
advanced Concept access control features: i.e. soft / hard
/ timed anti-passback, dual user, card and PIN, free access
via timezones etc. Card In / Card Out operation across
four doors using 8 card readers can be achieved with the
addition of the Reader Expander Board. Up to 64 Intelligent
Four Door Modules can be connected to a single Control
Module.
994012 Intelligent Four Door Access Module
995013 Reader Expander Board for Intelligent
Four Door Access Module
Two Door Access Module
The 2 Door Access Module is an economical two door,
two card reader access module. It can control two doors
with two readers, or one door with in and out readers.
Readers can be configured independently allowing mixed
technologies on the one Module. The Two Door Access
module fully supports the advanced Concept access control
features: i.e. soft / hard / timed anti-passback, dual user,
card and PIN, free access via timezones etc.
Where a measure of offline redundant access control is
required, the Cached version of the 2 Door Access Module
can be used. Up to 99 2 Door Access Modules can be
connected to a single Control Module.
995012 2 Door Access Module metal enclosure
995012PS 2 Door Access Module and power supply
in metal enclosure
995012CAPS 2 Door Access Module with with offline
cache mode and power supply in
metal enclosure
995012CAPCB&K 2 Door Access Module with with offline
cache mode short form kit
Single Door Access Module
The Single Door Access Module is an economical one door,
one card reader access module. It fully supports all of the
advanced Concept access control features. Up to 99 Single
Door Access Modules can be connected to a single Control
Module.
995011PCB&K 1 Door Access Module short form kit
IP Four Door Access Controller
The IP 4 Door Controller provides an advanced network
solution for fully integrated access control, security and
building automation systems. This product combines all the
I/O and processing requirements for access control, alarm
monitoring and automation functions for up to 4 doors, 10
areas and 16 zones. Two additional 2 Door Access Modules
can also be connected to provide control of up to 8 doors.
“Programmable Site Code” is also supported.
Whilst the IP 4 Door Controller provides a competitive
standalone solution for smaller sites, an unlimited number
of IP 4 Door Controllers can be linked and managed as one
system using the Insight software.
995002IPD IP 4 Door Access Controller
995012PCB-01 2 Door Expansion Kit
Standalone Two Door Access Controller
Designed for smaller applications, yet rich in features, the
Standalone Two Door Access Controller is a powerful access
control solution in an economical package. This device has
capacity for 100 users and has a 64 event non-volatile event
buffer. It boasts all of the access control features of the
standard 2 Door Access Module, but is designed to operate
without the need of a separate Control Module.
The Standalone 2 Door Access Module can be connected to
a PC for setup and system management.
995012SA Standalone Two Door Access Controller
in plastic utility enclosure.
Requires external power supply
995012SAPS Standalone Two Door Access Controller in
Small Low Profile Powered
Enclosure. (Contains 2A Power Supply)
993036 Port 0 Cable and IRSDAC software
995112SAUP Conversion kit. Converts Standalone Two
Door Access Controller to a Concept
4000 Cached 2 Door Access Module
Miscellaneous
Fibre Modem
Inner Range Single Mode and Multimode Fibre Modems
present a purpose built fibre optic solution designed
specifically to work with Concept installations. The Inner
Range Fibre Modem provides two separate, optically isolated
ports to the Concept system LAN. A set of Fibre Modems
are ideal for applications where modules in a Concept
system are in different buildings and/or are separated by
large distances. The Fibre Modems can work in loop or
branch modes.
995081 Fibre Modem (Multimode)
995087 Fibre Modem (Single Mode)
LAN Isolator
The LAN Isolator affords a Concept system with optical
isolation of LAN wiring with an optional LAN ‘loop’ mode.
The elimination of electrical connection between LAN
sections serves as a means to break earth loops as well as
extending the length of the LAN.
In addition to this, the LAN Isolator monitors its LAN sections
and can isolate sections of the LAN where problems are
discovered. Also provided are outputs to indicate the status
of the LAN allowing LAN section status and alarms to be
reported as required.
995080 LAN Isolator in metal enclosure
995080PCB&K LAN Isolator short form kit