JVC LWT0254-001B-H - Manual (Page 24)

24
EN
Setting Up the Camera Using RM-P2580 (continued)
CAMERA FUNCTION 1 Screen
Item Function/Set Value
Initial
Value
V. PHASE This adjusts the vertical synchronization to those of other cameras when a selector switch for
the synchronizing system on the Ceilling Mount is at LL. (50 Hz *(60Hz) power region only.)
*( ) : TK-C625U
Set values : TK-C625E : -156 to 0 to 156
TK-C625U : -131 to 0 to 131
0
POS.TITLE LOC. Use this to set the display positions of position and area titles.
UP-L
: Display at the top left of the screen. DOWN-C : Display at the lower center of the screen.
DOWN-L : Display at the bottom left of the screen. UP-R : Display at the top right of the screen.
UP-C : Display at the upper center of the screen. DOWN-R : Display at the bottom right of the screen.
[Set values: UP-L, DOWN-L, UP-C, DOWN-C, UP-R, DOWN-R]
UP-L
PRIVATE MASK.. This function grays out sections on the captured image that are not to be displayed. The
grayed out section moves accordingly during panning, tilting and zooming.
APRIVATE MASK SetupB (A pg. 31)
^
MANUAL DISPLAY Use this to set whether to display AMANUALB on the screen when manual operation is
performed at non-preset positions using the remote control unit. When this is set to AONB,
AAUTO PANB and AAUTO TRACEB will also be displayed on the screen respectively during
Auto Pan and Auto Trace operations, in addition to manual operation.
ON : Display "MANUAL".
OFF : Do not display "MANUAL".
MEMO
● Even when this item is set to AONB, display will not appear when the AAREA DISPLAYB (A pg. 26) item
is set to ATITLEB or ADIRB, or when a preset position is selected.
ON
CAMERA FUNCTION 2 Screen
Item Function/Set Value
Initial
Value
FLIP When Tilt operation is performed with this item set to AOFFB, the camera will stop at the
position where it is facing directly downwards. When an object passes beneath the camera,
the camera will A point downwards, B pan 180°, and C point upwards. In other words, the
camera needs to perform these 3 steps. By using the Auto Flip function helps to reduce the
number of operations.
Set this function when shooting an object that passes beneath the camera.
OFF
: Auto Flip is disabled.
AUTO 1 : The camera pans 180° automatically and stops when the object comes beneath
the camera. In this case, the camera and PAN/TILT lever operations function in
the same direction.
AUTO 2 : The camera pans 180° automatically when the object comes beneath the
camera, and direction of the camera and TILT lever operations function in
opposite directions. Set this function to enable continuous operation. Stopping
this operation restores the camera to its normal direction of operation.
AUTO 3 : The camera pans 180° automatically when the object comes beneath the
camera, and direction of the camera and TILT lever operations function in
opposite directions. The camera will return to its normal direction of operation
upon a lapse of 10 seconds or more after the operation stops.
OFF
VAR. P/T SPEED Use this to alter the Pan (horizontal) and Tilt (vertical) speed automatically according to the
zoom of the lens. Pan and Tilt speed will slow down when the zoom lens is set to TELE, and
speeds up when set to Wide. Set this when shooting objects with a different zoom ratio.
OFF : Disabled.
ON :
Enabled.
ON
EASY AF When this is set to ON, the auto focus (AF) function will be automatically activated during
manual Pan, Tilt or Zoom operation. This function is convenient when frequent manual
operations are expected as it eliminates the need to adjust focus after every manual
operation of the camera.
OFF : Disabled.
ON :
Enabled.
MEMO
● Auto focusing may sometimes fail to bring an object into accurate focus. (A pg. 6) In this case, adjust
focus manually.
OFF