JAI CV-A33CL - Manual (Page 21)

CV-A33CL
- 20 -
7.3. CV-A33CL command list
Command Name Format Parameter Remarks
A – General settings and useful commands
EB
Echo Back EB=[Param.]<CR><LF> 0=Echo off 1=Echo on Off at power up
ST Camera Status request ST?<CR><LF> Actual setting
HP Online Help request HP?<CR><LF> Command list
VN Firmware version VN?<CR><LF> 3 letter version
ID Camera ID request ID?<CR><LF> 10 characters
MD Model Name request MD?<CR><LF> ≤ 10 characters
UD User ID (Free text) TR=[Param.]<CR><LF> User can save and load free text ≤ 16 characters
B – Video Output
BA Output bit allocation BA=[Param.]<CR><LF> 0=10 bit 1=8 bit Camera Link
C – Timing and shutter related commands
WS
Windows Scan WS=[Param.]<CR><LF> 0=full frame 1=windows scan
WX X Scan start coordinate WX=[Param.]<CR><LF> 0-657 Start pixel #
WY Y Scan start coordinate WY=[Param.]<CR><LF> 0-490 Start line#
WW X Scan size width WW=[Param.]<CR><LF> 2-659 Window width
WH Y Scan size height WH=[Param.]<CR><LF> 3 – 493 Window height
AT Auto Trigger AT=[Param.]<CR><LF> 3-493 *)
Wind. 3H to 493H
TR Trigger mode TR=[Param.]<CR><LF> 0=normal
2=Pulse width 1=Edge pre-sel
3=Auto Trigger
SM Shutter mode SM=[Param.]<CR><LF> 0=Normal 1=Program. exp
SH Shutter speed SH=[Param.]<CR><LF> 0=Off (1/120)
2=1/500
4=1/2000
6=1/10000 1=1/250
3=1/1000
5=1/5000
7=1/20000
All 8 steps are
valid in normal
trigger mode.
PE Programmable expos. PE=[Param.]<CR><LF> 2-493 Exp. 1H to 492H
H= 16.8µsec
D– Signals and polarity
LS LVAL synchronous accum. LS=[Param.]<CR><LF> 0= LVAL sync. 1= LVAL a-sync. *1) Only a-sync.
TI Trigger Input TI=[Param.]<CR><LF> 0= CamerLink 1= 12 pin Hiror
TP Trigger polarity TP=[Param.]<CR><LF> 0= active low 1= active high *2)
E – Gain and analogue signals setting
BL
Black level BL=[Param.]<CR><LF> 0-31 (0=low 31=high)
GA Gain level GA=[Param.]<CR><LF> 1-11 (0=low 11=high)
CB Calibration of CMOS sensor CB=0<CR><LF> 0 is the only allowed parameter Will calibrate the
CMOS sensor
F – Saving and loading data in EEPROM
LD
Load settings from camera
EEPROM LD=[Param.]<CR><LF> 0=Factory data
2=User 2 area 1=User 1 area
Latest used data
default at power
up
SA Save settings to camera
EEPROM
SA=[Param.]<CR><LF> 1=User 1 area 2=User 2 area Parameter = 0 is
not allowed
*) Auto trigger window will always start from top. Max frame rate with AT=3. It is 2 LVAL exposure + 9 LVAL offset.
*1) The command LS is found on the first cameras. Only LS=1 is will work correct.
*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored. TTL only.
!! Do not try to use commands not shown in this list.