JVC DT-V24G1 - Manual (Page 16)

16
FUNCTION SETTING
Settings for the sub menu display, color system, color of the tally lamp, picture size, intensity of the button lamps
and the PHASE adjustment.
Item To do Setting value
sub menu
POSI. Select the contents and displaying position of “sub menu.” ☞ “NOTE”
COLOR
SYSTEM Select the color system.
• If the picture is unstable with “AUTO,” select “NTSC” or “PAL.” AUTO, NTSC, PAL
TALLY SELECT Select the color of the tally lamp. GREEN, RED
SD4:3 LARGE Change the picture size of 4:3 format signal. ☞ “NOTE”
DIMMER Select the intensity of the button lamps. NORMAL, DARK
COMPONENT
PHASE Deactivates the function of PHASE adjustment (Picture adjustment
knob and “PICTURE SUB ADJ.” in SET-UP MENU) except when an
NTSC signal comes in (
☞ 3 on page 6).
ENABLE, DISABLE
PICTURE SUB ADJ.
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.
Item To do Setting value
CONTRAST* 1 Adjust the standard level for the contrast adjusted with the
CONTRAST knob on the front panel. –20 – +20
BRIGHT* 1 Adjust the standard level for the brightness adjusted with the
BRIGHT knob on the front panel. –20 – +20
CHROMA* 1 Adjust the standard level for the chroma adjusted with the CHROMA
knob on the front panel. –20 – +20
PHASE* 1, * 2 Adjust the standard level for the phase adjusted with the PHASE
knob on the front panel. –20 – +20
NTSC SETUP Select the set-up level of the input NTSC signal. 00 (compliant with
0% set-up signal),
7.5 (compliant with
7.5% set-up signal)
COMPO. LEVEL Select the level of the analog component signal (480i and 576i only). B75 (compliant
with BetacamVTR
7.5% set-up signal),
B00 (compliant
with BetacamVTR
0% set-up signal),
SMPTE (compliant
with M2VTR signals)
sub menu Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while
viewing the actual picture.
reset Restore the default settings for all the items in “PICTURE SUB ADJ.”
* 1 Memorized for each input.
* 2 When “COMPONENT PHASE” is set to “DISABLE” and an NTSC signal is input, PHASE can be adjusted.
For the operation procedure, see page 7.
Operation guide
Shows the buttons for each
operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
Menu Configuration—SET-UP MENU
Settings of “sub menu POSI.”
The setting values and features are as follows.
LOWER1:
Displays the current setting and adjustment bar at the lower part of the screen.
UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.
LOWER2: Displays the current setting at the lower part of the screen.
UPPER2: Displays the current setting at the upper part of the screen.
• The adjustment bar is not displayed for some items.
Settings of “SD4:3 LARGE”
The setting values and features are as follows.
OFF:
Fit the vertical picture size into the pixel numbers of the monitor display.
ON: Fit the vertical picture size into that of the monitor display.
NOTE
DT-V24G1_20L3G_EN.indd 16 DT-V24G1_20L3G_EN.indd 16 10.1.15 3:22:23 PM 10.1.15 3:22:23 PM