JVC DT-V1910CG - Manual (Page 56)

22
<STATUS DISPLAY>
STATUS DISPLAY : ON
LEVEL METER ch :31•24
BAR TYPE :3COLORS
REFERENCE LEVEL : -20dB
OVER LEVEL
: -4dB
BAR BRIGHTNESS : HIGH
EXIT: MENU ADJUST:- + SELECT:
Ⅵ STATUS DISPLAY
Sets the status display ON or OFF.
ON : The information is displayed.
OFF : The information is not displayed.
Ⅵ LEVEL METER ch
Selects the audio channels used in the AUDIO
LEVEL METER display.
• OFF/1:2/12:34/31:24/123:456/1-8
NOTES:
• Numbers indicate the audio channel. The channel input level
indicated on the left side of “:” is displayed on the left side of the
screen, and the channel input level indicated on the right side of
“:” is displayed on the right side of the screen.
• AUDIO LEVEL METER is not displayed when this is set to OFF.
• When “1-8” is selected, the channel input level for 1, 2, 3 and 4 is
displayed on the left side of the screen, and the channel input
level for 5, 6, 7 and 8 is displayed on the right side of the screen.
Ⅵ BAR TYPE
Selects the colour of the audio level meter.
WHITE-1 : White colour display
WHITE-2 : White (half transparent) display
3 COLORS : The audio level meter uses three different
colours (red, yellow and green) to indicate
variations in input levels.
Red : displayed when the audio input exceeds the
level set in “OVER LEVEL”.
Yellow : displayed when the audio input exceeds the
level set in “REFERENCE LEVEL”.
Green : displayed when the audio input does not
exceed the level set in “REFERENCE
LEVEL”.
NOTES:
• For WHITE-1 and WHITE-2, the line indication for the standard
input level set in the “REFERENCE LEVEL” is displayed. Input
level set in the “OVER LEVEL” is not displayed.
• As for the audio channel bar display with no signal input, white is
displayed for the 3COLORS setting, and grey is displayed for
other settings.
Ⅵ REFERENCE LEVEL ( )
Sets the standard input level.
• –20dB/–18dB
CONTROL LOCK
Ⅵ CONTROL LOCK
Invalidates most of operations on the front panel
(including menu screen operations).
OFF : Enables normal operations.
ON : Invalidates all operations except the power switch
and CONTROL LOCK.
NOTES:
• While CONTROL LOCK is set to ON, attempting to perform any
operation except power switch and CONTROL LOCK causes the
“
Control lock on!” warning to appear on the screen for approx.
3 seconds. (It is possible to operate the power switch and display
SETUP MENU.)
• When SETUP MENU is displayed while CONTROL LOCK is set
to ON, the cursor (4) is located next to CONTROL LOCK and
cannot be moved.
all reset
Resets all SETUP MENU items to factory-preset
values.
1. Select “all reset” by / buttons, then press button.
Confirmation message is displayed.
2. To initialise, press button.
To cancel the initialization, press the MENU button.
STATUS DISPLAY
Sets the status display ON/OFF.
* Switches the display on and off. Also selects the type of
display. (When an input card compliant with AUDIO
LEVEL METER is installed.)
* Switches the AUDIO PLL setting. (When SDI input card
compliant with EMBEDDED AUDIO is installed.)
Press the button to
display the setting menu
illustrated on the right.
NOTE:
Function setting is displayed
when input card compliant with
AUDIO LEVEL METER is
installed.
1 2 3 4 5 6 7 8
Ⅵ OVER LEVEL ( )
Sets the input level’s lower limit indicated in red for
the “3COLORS” display.
• –8dB/–6dB/–4dB/–2dB
Ⅵ BAR BRIGHTNESS ( )
Selects the brightness of the AUDIO LEVEL METER
display.
HIGH : Brighter
LOW : Darker
AUDIO LEVEL METER display example
LEVEL METER ch: 1-8, BAR TYPE: 3COLORS
OVER LEVEL
[–8dB/–6dB/–4dB/–2dB]
REFERENCE
LEVEL
[–20dB/
–18dB]
Audio channels and OVER/REFERENCE
level indication
HOW TO USE “SETUP MENU”
(cont'd)
LCT1423-001A_p18-32 4/29/03, 5:08 PM 22