JVC Model DLA-HX1E - Manual (Page 11)

11
Control Panel on the Projector
Controls and Features
1
[STAND BY] Indicator
Light on : In stand by mode.
Blinking : In cool down mode.
2
[OPERATE] Indicator
Light on : During projection.
3
[OPERATE] button
When this projector is in standby mode, pressing this but-
ton for more than 1 second will turn the projector on and
cause the [OPERATE] indicator to light up. Press it one sec-
ond or more again, and the projector goes into the cool
down mode and finally into stand by mode. (
☞ page 25)
• The [OPERATE] button will not work within approximately
1 minute of the light-source lamp being turned on. Hence
wait about 1 minute before pressing.
4
[VOL.]
ª / · buttons
Use these buttons to adjust the sound volume.
(
☞ page 27)
5
[EXIT] button
Press this button to display the previous menu (For exam-
ple, from sub menu to main menu). Pressing this button
when the main menu is displayed will erase the menu.
(
☞ page 35)
6
[ENTER] button
Press this button to show the next menu (For example, from
main menu to sub-menu). It is also used when [ENTER] is
displayed against an item on the menu screen, or to choose
the “Reset” option etc. (
☞ page 35)
7
[HIDE] button
Use this button to temporarily halt the audio and video out-
put. Press again to resume. (
☞ page 29)
8
[TEMP] Indicator
Blinking : Indicates the temperature inside the projector is
abnormally high.
9
[LAMP] Indicator
Light on : Indicates the lamp has been used for more than
1900 hours.
Blinking : Indicates the lamp has been used for more than
2000 hours.
Please change the lamp. (
☞ page 10, 47, 55)
p
[VIDEO] button
Use this button to select a device such as a video con-
nected to the [VIDEO IN] terminal ([VIDEO] or [Y/C] Input
terminal) of the projector. (
☞ page 25)
q
[PC] button
Use this button to select a device connected to the [PC1],
[PC2] or [PC3] terminals. (
☞ page 26)
w
[H-KEYSTONE] button
Use this button to remove the horizontal trapezoidal distor-
tion of the image projected on the screen. (
☞ page 30)
e
[V-KEYSTONE] button
Use this button to remove the vertical trapezoidal distortion
of the image projected on the screen. (
☞ page 30)
r
[MENU] button
Use this button to enter or exit the menu mode. When the
main menu is displayed, pressing this button will cause the
menu to disappear. (
☞ page 35)
t
Cursor ( ᮡ / ᮢ / ᮤ / ᮣ ) buttons
These buttons are used in the menu mode to select an
item, adjust the value etc. (
☞ page 35)
y
[PRESET] button
This [PRESET] button only works as a reset button for the
[VOL.], [V-KEYSTONE] and [H-KEYSTONE] adjustments
done on the control panel and the [VOLUME], [V-KEY-
STONE], [H-KEYSTONE] and [DIGITAL ZOOM] adjust-
ments done on the remote control. (
☞ page 28, 30)
When adjusting the volume, keystone or digital zoom (when
the setting is displayed on the screen) the adjusted value is
reset to that which was set when the projector was shipped
from the factory. This button does not work for the menu
(submenu) items.
About Cool Down mode
After projection, the heated lamp will go through a 90 sec-
onds cool-down period known as the cool down mode. This
function is to prevent heat from the heated lamp causing
damage and deformation to the internal components of the
projector. It also prevents lamp breakage and shortened lamp
life.
The Cool down mode is indicated by the blinking [STAND
BY] indicator. During the cool down mode, pressing the
[OPERATE] button will not turn on the projector.
After the cool down process is completed, the projector will
automatically change to stand by mode.
Note
Please do not pull out the plug from the power outlet during
cool down mode. Please also do not block the exhaust vent
by standing the projector on its end or laying it on its side.
HX-1E_p05-14_En.p65 10/3/03, 6:07 PM 11