JVC HR-5910U - Manual (Page 17)

EN
17
6
Access Cable Box Brand Set screen
Press OK.
7
Enter cable box brand
Press the appropriate
Number keys to enter
the brand code from the
list shown to the right,
then press OK.
● If the cable box’s
channel changes to 9,
setting is complete
Press OK and “CABLE
BOX CONTROL IS
ON” appears on the
screen for about 5
seconds, then it
returns to the normal
screen.
● If the cable box's channel does not change to 9
1 Press SHUTTLE PLUS %fi to move the
highlight bar (arrow) to “NO”.
2 Press OK.
3 Repeat step
7 until the cable box’s channel
changes to 9 by entering another code.
4 If the channel does not change after going
through all the code numbers listed for your
model of cable box, then try all the other
numbers between 1 and 25.
CABLE BOX BRAND LIST
BRAND CODE
ARCHER 1, 5, 17
CABLETENNA 1, 17
CABLEVIEW 15, 16, 17, 21, 25
CITIZEN 15, 16, 17, 21, 25
CURTIS 2, 8
DIAMOND 1, 17
EASTERN 19
GC BRAND 15, 16, 17, 21, 25
GEMINI 15
GENERAL INSTRUMENTS 1, 4, 6, 11, 12, 15, 28
HAMLIN 10, 18, 19, 23
JASCO 15
JERROLD 1, 4, 6, 11, 12, 15, 28
NOVAVISION 2, 8
OAK 7, 20
PANASONIC 13, 14
PULSER 15, 16, 17, 21, 25
RCA 13, 14
REGAL 10, 18, 19, 23
REGENCY 19
REMBRANDT 1, 16, 17
SAMSUNG 5, 16, 24
SCIENTIFIC ATLANTA 2, 8
SIGMA 7, 20
SL MARX 5, 16, 17, 24, 25
SPRUCER 13, 14
STARGATE 5, 15, 16, 17, 21, 24, 25
TELEVIEW 5, 16, 24
TOCOM 1, 4, 16
UNIKA 1, 17
UNIVERSAL 16, 17, 25
VIDEOWAY 3, 9, 22
ZENITH 3, 9, 22
If the VCR’s clock has not been set (with AUTO
CLOCK set to ON)
“CABLE BOX USERS SET CLOCK MANUALLY” appears for
about 5 seconds when you press OK in step
6, then the
Clock Set screen appears.
Perform Manual Clock Set on page 12. If you press MENU
after the clock has been set, the Cable Box Brand Set
screen appears.
CABLE BOX BRAND SET
1
PRESS NUMBER KEY (0–9)
THEN (OK) TO TEST
PRESS (MENU) TO END
NOTES:
● The Controller may not work with all types of cable box.
● If your cable box does not respond to any code between 1
and 25, you cannot use the Controller to change cable box
channels. In this case, make sure to leave the cable box
turned on and tuned to the proper channel before the
scheduled start time of timer recording.
Contact your cable company about the possibility of
exchanging your current cable box with the one compatible
with your VCR.
● The VCR can only change the cable box channel through the
Controller during timer recording.
● If your cable box cannot be operated with a remote control
(because it has no remote sensor), you cannot use the
Controller to change its channels. Make sure to leave the
cable box turned on and tuned to the proper channel before
the scheduled start time of timer recording.
● If the VCR’s memory backup expires because of a power
failure, set the cable box output channel and brand again.
● For customers in U.S.A.: If you are unable to set the
Controller, contact JVC toll free at 1-800-537-5722.
CABLE BOX BRAND SET
1
DID YOUR CABLE BOX
CHANGE TO CHANNEL 09?
= YES
NO
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END