JVC KD-AR470 - Manual (Page 83)

KD-G524
Installation/Connection Manual
0905DTSMDTJEIN
EN
1
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
J
Handles
F
Washer (ø5) G
Lock nut (M5) H
Mounting bolt (M5 x 20 mm)
I
Rubber cushion
A / B
Hard case/Control panel C
Sleeve D
Trim plate
E
Power cord
Parts list for installation and connection
The following parts are provided for this unit. After checking them, please set them correctly.
K
Remote controller L
Battery
Do the required electrical
connections.
* 1 When you stand the unit,
be careful not to damage the
fuse on the rear.
Bend the appropriate tabs
to hold the sleeve firmly in
place.
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealers or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
GET0338-002A
[UI]
When installing the unit without
using the sleeve
In a Toyota for example, first remove the car radio
and install the unit in its place.
When using the optional stay
Note : When installing the unit on the mounting
bracket, make sure to use the 8 mm-long
screws. If longer screws are used, they could
damage the unit.
* Not supplied for this unit.
Screw (option)
Stay (option)
Fire wall
Dashboard
Install the unit at an
angle of less than
30˚.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
Bracket *
Pocket
Flat type screws
(M5 x 8 mm)
*
Bracket *
WARNINGS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealers.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than
50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 13 of the
INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with
insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when
removing this unit.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
© 2005 Victor Company of Japan, Limited
Flat type screws
(M5 x 8 mm)
*
Heat sink
Install_KD-G524[UI]f.indd 1 Install_KD-G524[UI]f.indd 1 9/13/05 6:41:54 PM 9/13/05 6:41:54 PM