JVC 0506TKH-VT-VT - Manual (Page 15)

- 14 -
Tips
Can not turn the TV on?
Check that TV/VCR/DVD switch is set to TV position.
TV may go to stand-by mode when you turn the TV on soon
after you turn the TV off. If you can turn the TV on again, it is
not a problem.
Can not turn the TV off?
Check that TV/VCR/DVD switch is set to TV position.
Care of the Screen
Clean the screen with a slightly damp, soft cloth. Do not use
abrasive solvents as they may damage the TV screen coating
layer.
Colours of image on screen are abnormal
Have you selected the correct TV system? Is your TV set or
house aerial located too close to the loudspeakers, non-earthed
audio equipment or neon lights, etc. ?
Mountains or high buildings can cause double pictures or ghost
images. Sometimes you can improve the picture quality by
changing the direction of the aerial.
Is the picture or Teletext unrecognisable? Check if you have
entered the correct frequency.
The picture quality may degrade when two peripherals are
connected to the TV at the same time. In such a case, dis-
connect one of the peripherals.
No Image on Display Screen
Is the aerial connected properly? Are the plugs connected
tightly to the aerial socket? Is the aerial cable damaged? Are
suitable plugs used to connect the aerial? If you are in doubt,
consult your dealer.
No Image means that your TV is not receiving any transmis-
sion. Have you pressed the correct buttons on the remote
control? Try once more.
Sound
You can not hear any sound. Did you perhaps interrupt the
sound, pressing “ ” button? Are external speakers connected
to the TV?
Sound is coming from only one of the speakers. Is the bal-
ance set to one direction extreme? See Sound menu.
Remote Control
If your TV no longer responds to the remote control, perhaps
the batteries are exhausted. Replace the batteries.
Have you selected the wrong menu?
Press “MENU” button to
return to normal screen.
No solution
If the TV suddenly stops responding, disconnect the power
cord of the TV from the AC outlet. Connect it to the AC outlet
again to turn on the TV. If the TV returns to a normal state, it is
not a failure. If this does not work, switch off, remove the mains
plug and call the service personnel; never attempt to repair it
yourself.
Specifications
Broadcasting System
PAL SECAM B/G D/K K’ I/I’ L/L’
Channels and Frequencies
Analogue: 46.25 MHz - 862.25 MHz (channel 01-17/21-73)
Cable TV: S1 - S41
Sound System
A2+Nicam Stereo
Power Requirements
220-240 V AC, 50 Hz
Power Consumption
105 W (Standby < 3W)
Picture Tube Size
Viewable area
70 cm.(measured diagonally)
Audio Output
2x10 W RMS (10% THD)
EXT.1 Terminal
Euroconnector (21-pin, SCART)
* Video Input, Audio L/R Inputs and RGB Inputs are available.
* Analogue TV broadcast output (Video and Audio L/R) are
available.
EXT.2 Terminal
Euroconnector (21-pin, SCART)
* Video Input, S-VIDEO (Y/C) Input, Audio L/R Inputs are avail-
able.
* Video and Audio L/R outputs are available.
* T-V LINK functions are available.
EXT.3 Terminal
RCA connectors x 3
* Video Input and Audio Inputs are available.
Headphone jack
Stereo mini-jack (3.5 mm in diameter)
Dimensions (WxHxD)
760 mm x 570 mm x 473 mm
Accessories
Remote control unit x 1
(RM-C1100)
AA/R6 dry cell battery x 2
A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p65 22.05.2006, 13:45 14