JVC 0506TKH-VT-VT - Manual (Page 5)

- 4 -
Preparation
For ventilation, leave a space of at least 10 cm free all around
the set. To prevent any fault and unsafe situations, please do
not place any objects on top of the set.
Use this apparatus in moderate climate.
Features
• It is a remote controlled colour television.
• 100 programmes from VHF, UHF bands or cable channels
can be preset.
• It can tune cable channels.
• Controlling the TV is very easy by its menu driven system.
• It has two Euroconnector sockets for external devices (such
as computer, video, video games, audio set, etc.)
• A2+NICAM Stereo sound system.
• Teletext (Fastext, Toptext).
• It is possible to connect headphone.
• Direct channel access.
• A.P.S. (Automatic Programming System).
• All programmes can be named.
• Programme swapping between last watched two programmes.
• Forward or backward automatic tuning.
• Sleep timer.
• Child Lock.
• Automatic sound mute when no transmission.
• When no valid signal is detected, after 5 minutes the TV
switches itself automatically to stand-by mode.
• NTSC Playback.
• S-VHS (via SCART)
Before Switching on your TV
Power connection
IMPORTANT: The TV set is designed to operate on 220-240V
AC , 50 Hz.
• After unpacking, allow the TV set to reach the ambient room
temperature before you connect the set to the mains.
Connections to the RF input socket
• Connect the aerial or cable TV plug to the RF input socket
located at the back of the TV and connect the cable plug
coming out from the TV out socket located at the devices
(VCR, DVB etc.) to this socket as well.
How to connect other devices
IMPORTANT: Switch off the TV before connecting any exter-
nal device.
Sockets for external connections are at the back and
on the
TV. For connection of other devices via Euroconnector refer to
the manuals of the related devices.
Inserting batteries into the remote control
• Remove the battery cover located on the back of the remote
control by gently pulling downwards from the indicated part.
• Insert two AA (R06) or equivalent type batteries inside. Place
the batteries in the right directions as seen below.
• Replace the battery cover.
NOTE: Remove batteries from remote control when it is not to
be used for a long period. Otherwise it can be damaged due to
any leakage of batteries.
Switching the TV ON/OFF
To switch the TV on
Your TV will switch on in two steps:
1- Press the power button located on the front of the TV. Then
the TV switches itself to standby mode and the power lamp
becomes RED located on the lower part of the TV.
2- To switch on the TV from stand-by mode either:
Press the “
 , ” button on the remote control,
or,
Press a digit button on the remote control so that a programme
number is selected,
or,
Press Programme Up or Down buttons on the TV or on the
remote control, so that last switched off programme is se-
lected.
The TV will switch on and the power lamp will be GREEN.
To switch the TV off
• Press the stand-by button on the remote control, so the TV
will switch to stand-by mode and the power lamp will be-
come RED,
or,
• Press the power button located on the front of the TV, so the
TV will switch off and the power lamp will turn off.
Initial Settings
When the TV is first turned on, it goes into the initial settings
mode. Follow the instructions on the screen display to make
the initial settings.
Note: If the TV does not go into the initial settings mode this is because your TV has
already been turned on for the first time. (Perform “AUTO STORE” ( see page 9 ) in the
PROGRAMME menu.)
Because this is the first time that TV has been used, there are
no channels stored in the memory. Analogue terrestrial broad-
casting AUTOMATIC PROGRAMMING SYSTEM (A.P.S.) win-
dow is displayed.
QG@6T@Ã 8C@8FÃ 6IU@II6Ã 867G@
6VUPTUPS@
8PVIUS`
G6IBV6B@
8PIUDIV@
VF
@IBGDTC
6ÃQÃT
A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p65 22.05.2006, 13:45 4