JVC DLA-G150CLE - Manual (Page 75)

DLA-G150CLU DLA-G150CLE
1-75
No.51931
68
Warning Messages
• When the DIGITAL ZOOM button
is pressed for the video signals
that cannot be zoomed (UXGA
60Hz, SXGA 60Hz.), this
message appears for a few
seconds to notify that the image
cannot be digitally zoomed.
* To forcibly clear the message,
press the EXIT button.
• Digital-zoom function does not
work for the inputted video
signals.
To use the this function, input the
video signals that can be digitally
zoomed.
13, 37
Displayed when the lamp control
setting is set to NORMAL MODE
• Appears every time the projector
is turned on after the lamp use
time has exceeded 900 hours and
until it reaches 1000 hours.
* The message is cleared by
pressing any button.
• Arrange for a new lamp (lamp
unit) or replace the lamp early.
44, 46
Displayed when the lamp control
setting is set to NORMAL MODE
• When the lamp use time reaches
1000 hours, the word “Warning”
blinks on the screen.
* To cancel this message, press
the EXIT button.
However, the same message will
appear every hour.
* If the power is turned off after the
lamp use time has exceeded
1000 hours, the power can not be
turned on again.
* When the lamp use time reaches
1010 hours, the projector is
forcibly turned off and can not be
turned back on again.
• Replace with a new lamp (lamp
unit) and reset the lamp time.
44, 46
Message Cause Corrective action Page
D.ZOOM
EXIT
Lamp replacement
EXIT
Warning
Lamp replacement
67
ENGLISH
DEUTSH
FRAN
ÇAIS
ITALIANO
ESPAÑOL
Warning Messages
The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take
the corrective action described here.
Message Cause Corrective action Page
• No device is connected to the
input terminal.
• The terminal is connected but no
signal is output from the
connected device.
* The selected input mode (input
terminal) name is shown in the
first line of the massage.
• Connect a device to the selected
terminal.
• Operate the connected device
and output a signal.
9, 11,
24 ~ 29,
33
• The frequency of the input video
signal is out of range.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals whose
frequency is within the projector’s
specifications.
22, 23,
70
• Though the frequency of the input
video signal is within the
acceptable range, other items
such as resolution are out of the
projector’s specifications.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals that
satisfies the projector’s
specifications.
22, 23,
70
• When the FREEZE button is
pressed, this message appears
for a few seconds.
• When a button not acceptable is
pressed during freezing, this
message appears for a few
seconds to notify that the image is
being frozen.
• To release freezing, press the
FREEZE button on the remote
control.
12, 37
• When the FREEZE button is
pressed for the video signals that
cannot be frozen (UXGA 60Hz,
SXGA 60Hz.), this message
appears for a few seconds to
notify that the image cannot be
frozen.
* To forcibly clear the message,
press the EXIT button.
• Freeze function does not work for
the inputted video signals.
To use this function, input the
video signals that can be frozen.
12, 37
P C 1
N o I n p u t
P C 1
F r e q u e n c y o f i n p u t s i g n a l i s o u t o f r a n g e .
P C 1
S i g n a l i s n o t s u p p o r t e d .
FREEZE
FREEZE