JVC RX-1024VBK - Manual (Page 40)

37
Using the Theater Surround Mode
Once you have adjusted the Theater Surround mode, this receiver memorizes the
adjustment. To activate the Theater Surround mode, follow the procedure below.
From the remote control:
1. Select and play the source encoded with Dolby Digital (bearing the mark
D I G I T A L
) or with Dolby Surround (bearing the mark
DOLBY SURROUND
).
• When you play back the source encoded with Dolby Digital and select the digital
input for that source, the
Ÿ DIGITAL indicator lights up on the display.
2. Press SURROUND MODE repeatedly until “THEATER”
or “DIG-THEATER” appears on the display.
The DSP and THEATER indicators also light up on the display.
Each time you press the button, the DSP modes change as follows:
When the digital input is selected to play the source encoded with Dolby
Digital:
For other sources:
If you need to make any adjustment, go to the following steps.
3. Press SOUND.
10 keys are activated for sound adjustments.
4. Press TEST to start checking the speaker output balance.
“TEST TONE L” starts flashing on the display, and a test
tone comes out of the speakers in the following order:
Notes:
• To enjoy the software encoded
with Dolby Digital, you must
connect the source
component using the digital
terminal on the rear of this
receiver.
• The Surround mode is not
used with the other DSP
modes such as the DAP mode
and 3D-PHONIC mode. When
the Surround mode is turned
on, the other DSP mode, if
used, will be turned off.
Using the DSP Modes
Notes on the indications:
• The PRO LOGIC indicator
lights up when the Dolby Pro
Logic decoder built in this
receiver is activated.
• The Dolby Pro Logic decoder
is used not only for the analog
sources but also for the
sources encoded with Dolby
Digital in the following cases:
– When only front channel
signals are encoded.
– When front channel and
monaural rear channel
signals are encoded.
While the Dolby Pro Logic is
activated for this type of Dolby
Digital source, the
Ÿ
DIGITAL
indicator goes off.
DOLBY DIGITAL DIG-THEATER
HEADPHONE 3D DIGITAL OFF
HALL
DANCE CLUB LIVE CLUB THEATER PRO LOGIC
3D ACTION HEADPHONE 3D DRAMA
PAVILION
3D THEATER
OFF
(Left front speaker) (Center speaker) (Right front speaker)
(Left rear speaker) (Right rear speaker)
TEST TONE L TEST TONE C TEST TONE R
TEST TONE RS TEST TONE LS
Notes:
• No test tone comes out of the
center speakers when
“CENTER SPK” is set to
“NONE” (see page 19).
• No test tone comes out of the
rear speakers when “REAR
SPK” is set to “NONE” (see
page 19).
• If the TV is turned on and the
proper video input is selected
on the TV, the test tone
screen will appear on the TV.
The speaker indicators also light on the display while the test tone
comes out of the speakers.
L:
Lights when the test tone comes out of the left front speaker.
C: Lights when the test tone comes out of the center speaker.
R: Lights when the test tone comes out of the right front speaker.
RS: Lights when the test tone comes out of the right rear speaker.
LS:
Lights when the test tone comes out of the left rear speaker.
C
LS
L
RS
R
IMPORTANT:
• Output the test tone while playing back an audio source.
With the DVD digital input selected as the source, no test tone may come out while
no signal is input to this receiver.
• Test tone comes out even while playing back a source encoded with Dolby Digital. In
this case, the PRO LOGIC indicator lights up on the display.
MODE
SURROUND
SOUND
TEST
4
EN28_40.RX-1024V[J]/1.PM5 98.5.12, 0:26 PM 37