JVC GM P420UG - Manual (Page 29)

27
2
Press 5/∞ to move the cursor (3) to
“HD SIGNAL MODE.”
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
3
Press 2/3 to select the desired setting.
Each time you press the button, the HD signal type
alternates between “1080i” and “1035i.”
• You can select either “1080i” and “1035i” according to
the HD signal you input — whichever gives you
proportionally shaped pictures.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
Using the Pixel Shift Function
This function periodically shift the position (pixels) of the
displayed picture on the screen so that you can avoid the
screen from being burned in.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding
2 to display
the Setup Menu.
2
Press 5/∞ to move the cursor (3) to
“PIXEL SHIFT” (on the second page).
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
3
Press 2/3 to select the desired setting.
Each time you press the button, the Pixel Shift function
alternates between “ON” and “OFF.”
To cancel the Pixel Shift function,
select “OFF.”
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
Cursor ( 3 ) S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
S E T - U P M E N U 1 / 2
A D J U S T : S E L E C T : E X I T : M E N U
: O F F
: O F F
: M O D E 1
: 1 0 8 0 i
3
Press
2/3 to select the desired setting.
Each time you press the button, the Remote Switch
Mode changes as follows:
MODE1 : Input alternates between “VIDEO A” and
“VIDEO B” when controlled from the external
control unit.
MODE2 : Input alternates between “VIDEO A” and
“RGB B/COMPO.” when controlled from the
external control unit.
MODE3 : Input alternates between “VIDEO A” and
“RGB A” when controlled from the external
control unit.
MODE4 : Input alternates between “VIDEO B” and
“RGB B/COMPO.” when controlled from the
external control unit.
MODE5 : Input alternates between “VIDEO B” and
“RGB A” when controlled from the external
control unit.
MODE6 : Input alternates between “RGB B/COMPO.”
and “RGB A” when controlled from the
external control unit.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
Setting the High-Definition Signal Types
You can select one of the High-Definition (HD) signal types
through the COMPONENT/RGB B terminals — 1080i or
1035i. Normally set it to “1080i.”
• Without setting “RGB/COMPO.” correctly, you cannot
show any picture though you select the COMPONENT
input (see page 23).
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding
2 to display
the Setup Menu.
Cursor ( 3 ) S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
S E T - U P M E N U 1 / 2
A D J U S T : S E L E C T : E X I T : M E N U
: O F F
: O F F
: M O D E 1
: 1 0 8 0 i
P I X E L S H I F T
P O W E R S A V E
C O L O R - R E V E R S E
R E F R E S H
r e s e t
a l l r e s e t
H O U R M E T E R x 1 0 0 h
M O D E L N A M E
S E T - U P M E N U 2 / 2
: O N
: O N
: O N
: O N
: 0 0 1
: G M - P 4 2 1 U
24-30.GM-P420[US]f 02.4.1, 2:21 PM 27