JVC Rear Projection Television HD-52Z575 - Manual (Page 9)

(No.YA092B)1-9
2.1.7 SUB (CHASSIS) CPU PIN FUNCTION (IC7001 : MN102H60KPA) [DIGITAL SIGNAL PWB ASS’Y]
Pin Port Pin name I/O Function
1 P60 LB PRO O Not use
2 P61 P MU O Picture muting [Muting = H]
3 P62/FUNC LED JP_CSB O Not use (NC)
4 P63 A MU O Audio muting [Muting = H]
5 P50 M MU O Audio muting (for AUDIO OUT) [Muting = H]
6 P51/PC SW PC SEL O Not use : RGB(PC) INPUT select
7 P52/DIMMER
LED
ON_TIMER O POWER INDICATOR (LED) brightness
[LOW = L]
8 P53/BL ON ILA0 O Not use : LCD back light lighting
9 P54/BL 5060 ILA1 O Not use : LCD panel overshoot refresh timing
10 P55 ILA2 O Not use
11 P56 POW LED O POWER LED lighting [ON = H]
12 P57 WORD O Not use
13 SBT2 MI_CK I Clock for SUB (OSD) CPU communication
14 SBI2 MI_TX I Data receive for SUB (OSD) CPU communication
15 SBO2 MI_RX O Data transmission for SUB (OSD) CPU
communication
16 P23/REQ MI_REQ O Data request for SUB (OSD) CPU communication
[Request = L]
17 VDD 3.3V I 3.3V power supply
18 PB0 FOSC O Not use (NC)
19 VSS GND Ground
20 XI 3.3V I Not use : Low speed oscillatior
21 XO O Not use : Low speed oscillatior
22 VDD 3.3V I 3.3V power supply
23 OSCI OSCI I System clock osillation (crystal) : 16MHz
24 OSCO OSCO O System clock osillation (crystal) : 16MHz
25 MODE 3.3V I Single chip mode
26 P24 BS1.5CTL O Not use : Digital tuner power / reset control
27 P25 A92 RST O Reset for IC1001(3D YC SEP / COLOR
DEMODULAT) [Reset = H]
28 P26 BS RST O Not use: Reset for Digital tuner power / reset
control
29 P27 LIP RST O Not use: Reset for Sound delay (Lip sync)
30 KI0 SOFT_OFF O Not use
31 KI1 VMUTE I No use : Picture muting request from digital tuner
32 KI2 VOUTENB O No use : Video cutoff for digital tuner
33 P33 MDR CON I No use : System cable connection monitor for PDP
34 AVDD 3.3V I 3.3V power supply
35 P34 O Not use : Digital tuner power control
36 P35 DSYNC SW2 O Sync select for DIGITAL-IN [Cotrolled with 99-pin]
37 P36 LB_POW O Not use : Power control for low bias line
38 P37 O Not use (NC)
39 P40 HOTPLUG I Not use : Video communiation monitor for receiver
unit (PDP)
40 P41 MECA SW I Mechanical monitor for POWER switch
[Push = L]
41 P42 MAIN POW O Main power control [ON = L]
42 P43 VARI/FIX O AUDIO OUT output mode select [VARI ABLE = L]
43 VREF- I Not use
44 AN4/EE AFT2 I Not use : AFT voltage for sub tuner
45 AN5 AFT1 I AFT voltage for VHF/UHF tuner
46 AN6 KEY2 I Key scan data for front switc (MENU/CH+/CH-)
47 AN7 KEY1 I Key scan data for front switch (VOL+/VOL-)
48 P80 O Not use (NC)
49 P81 O Not use (NC)
50 TM0IO AC IN I AC power pulse for timer clock
Pin Port Pin name I/O Function
51 SBI3 BS TXD O Not use : Data transmission for digital tuner
communication
52 SBO3 BS RXD I Not use : Data receive for digital tuner
communication
53 P85 O Not use (NC)
54 VREF+ 3.3V I 3.3V power supply
55 SBI4 PDP TX O Data transmission for SUB (DRIVE) CPU
communication
56 SBO4 PDP RX I Data receive for SUB (DRIVE) CPU
communication
57 P90 SDA0 I/O Data for Inter IC (serial) bus : EEP-ROM (IC7002)
58 P91 SCL0 O Clock for Inter IC (serial) bus : EEP-ROM (IC7002)
59 P92 SDA DVI I/O Not use : Data for Inter IC (serial) bus for panel
communication
60 P93 SCL DVI O Not use : Clock for Inter IC (serial) bus for panel
communication
61 AVSS GND Ground
62 AN0/DIN PH DIGII_PHOT I Photo sensor for DIGITAL-IN illegal copy
protection
63 AN1 ATSC REC I Not use
64 AN2 I Not use
65 AN3 I Not use
66 VDD 3.3V I 3.3V power supply
67 P70/DIN PRO DIGI_PRO O for DIGITAL-IN (HDMI)
68 P71 O Not use (NC)
69 P72 O Not use (NC)
70 P73 SYNC SEL O Not use : Sync select for digital tuner
71 SBI1 O Not use (NC)
72 SBO1 O Not use (NC)
73 * SBD5 I/O Not use : Data for writing on board
(connect CN01P : for Frash ROM type)
74 * SBT5 I Not use : Clock for writing on board
(connect CN01P : for Frash ROM type)
75 NMI 3.3V I 3.3V power supply
76 IRQ0 COMP I AV COMPULINK áV control
77 IRQ1 REMOCON I Remote control
78 IRQ2 V SYNC I V. sync pulse
79 IRQ3 WAKEUP SHM I Reset for sub(chassis) CPU
80 IRQ4 POWERGOOD I Power error detection [NG = H]
81 PA5/REC
LED
LAMP LED O LAMP LED lighting [Lighting = H]
82 VDD RST I Reset for MAIN CPU [Reset = L]
83 RST 3.3V I 3.3V power supply
84 P00 SCL3A O Clock for Inter IC (serial) bus control :
85 P01 SDA3A I/O Data for Inter IC (serial) bus control :
86 P02 SCL3B O Clock for Inter IC (serial) bus control :
87 P03 SDA3B I/O Data for Inter IC (serial) bus control :
88 P04/DIN SEL DIGI_SYNCSEL O Not use
89 P05 LR SW O for DIGITAL-IN (HDMI)
90 P06/DIN INT DIGI_INT I Reset for HDMI process [Reset = ]
91 P07 DVI RST O Not use : Reset for DVI format conversion
92 VSS GND Ground
93 P10 SCL5055 O Clock for Inter IC (serial) bus :
JCC5055 (DIST process)
94 P11/BS CLK
SEL
VFORMATSEL O Not use : Digital tuner clock control
95 P12 SDA5055 I/O Data for Inter IC (serial) bus :
JCC5055 (DIST process)
96 P13 OSD MODE SEL O Not use : OSD mode select
97 P14 O Not use (NC)
98 P15 15K/OTH O Main video select [Fixed H]
99 P16 DSYNC SW1 O Sync select for DIGITAL-IN [Cotrolled with 36-pin]
100 P17 JCC5057 BUSY I Busy monitor for JCC5057 (New DIST process)