JVC TK-C676 - Manual (Page 33)

33
HOME MOTION DETECT Setup
Use the HOME MOTION DETECT screen to set the areas to be excluded from the target area of the motion detect function. (which
outputs an alarm upon detection motion in the monitored picture)
1.
Select the camera. (
☞
RM-P2580 Instruction manual)
CAMERA button
→ Numeric key (camera number) → ENTER button.
The picture of the selected camera is output.
2.
Display the SETUP menu on the camera.
(
☞
P. 18, steps 1 to 4 )
MENU button (3 sec.) → Select “CAMERA” with the PAN/TILT lever
→ SET button.
The camera moves to the home position.
3.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to “HOME POSITION DETECT” and press
the SET button.
The HOME POSITION DETECT menu is displayed.
4.
Move the cursor (>) to “AREA EDIT” and press the
SET button.
The AREA EDIT setting screen is displayed. (The frame display
position is moved slightly upward from the center of the screen.)
5.
Tilt the PAN/TILT lever to select the area to be ex-
cluded from the motion detection target area.
The area blinking in white is moved by the operation of the lever.
6.
Press the SET button.
• The area to be excluded is set and blinks in gray.
• To cancel, press the SET button again.
• When the setting is canceled, the gray blinking changes to white
blinking.
7.
Repeat steps 5 and 6 for each area to be excluded
from the motion detection target area.
Complete the setup of all excluded areas in this way.
8.
Press the MENU button.
The screen returns to the precious menu.
SETUP
MENU SET
SPEED
IRIS
AF
FOCUS
ZOOM
OPEN
FAR
TELE CLEAR /HOME
7
4
1
8
0
5
2
9
6
3
ENTER
AUTO
PAN
OPTION
1
OPTION
2
CAMERA POSI- TION
AUTO
PATROL
CLOSE
NEAR
WIDE
AUTO F-1 F-2 F-3
PAN/TILT LENS CAMERA/POSITION
CAMERA POSITION
REMOTE CONTROL UNIT RM-P2580
ALARM
POWER
KEY LOCK
PAN/TILT
lever
CAMERA
buttons
ENTER
button
Numeric keys
SET button
MENU button
SETUP menu display on the camera
C A M . F U N C T I O N . .
– – – M E N U – – –
C A M . T I T L E / A L A R M . .
C A M . V I D E O A D J U S T . .
C A M . A L C / E x D R . .
H O M E M O T I O N D E T E C T . .
A U T O P A N / P A T R O L / T R A C E . .
P O S I . F U N C T I O N S E T . .
F A C T O R Y S E T T I N G S . .
HOME MOTION DETECT menu
M O D E O F F
– – – H O M E M O T I O N D E T E C T – – –
L E V E L – – –
A R E A E D I T . .
A L A R M D I S P L A Y 5 s
D E M O N S T R A T I O N . .
AREA EDIT screen
Blinking
– – – D E M O N S T R A T I O N – – –
DEMONSTRATION screen
The positions of areas in the picture are reference positions. Check the actu-
al positions in the actual picture.
The areas set to be excluded from the motion detection target area can be
confirmed in the DEMONSTRATION screen.
MEMO
The motion detect function is not intended to prevent fire or theft. There-
fore, JVC will not assume any liabilities for accidents and damage relat-
ed to the use of this function.