Document Outline

• Notice
• Warranty
• Certifications
• WARNING
• Table of Contents
  • Table of Contents v
  • List of Figures vii
  • List of Tables ix
  • 1 Introduction 1
  • 2 Installation 5
  • 3 Operation 15
  • 4 Troubleshooting 27
  • 5 Appendix 29
• List of Figures
• List of Tables
  • TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera
    • Operation Manual
• 1 Introduction
  • 1.1 Product Description
  • 1.2 Features
  • 1.3 Functional Options
  • 1.4 System Configuration
    • FIGURE 1. TM-2016-8 System Configuration
    • FIGURE 2. Camera Link System Configuration
• 2 Installation
  • 2.1 Getting Started
    • 2.1.1 Unpacking Instructions
    • 2.1.2 Components List
    • 2.1.3 Accessories and Options
  • 2.2 Camera Setup
    • 2.2.1 Heat Dissipation
    • 2.2.2 Connector Pin Configurations
      • 2.2.2 (a) 12-Pin Connector (TM-2016-8)
        • TABLE 1. 12-Pin Connector (TM-2016-8)
      • 2.2.2 (b) 12-Pin Connector (Camera Link models)
        • TABLE 2. 12-Pin Connector (TM-2016-8CL)
      • 2.2.2 (c) Digital Output Connector
        • FIGURE 3. Rear Panel View of Digital Connector
      • 2.2.2 (d) Camera Link Connector (Camera Link only)
        • TABLE 3. 31-Pin Connector (MP211-031-113-4300)
        • TABLE 4. Connector and Pinout Configurations
      • 2.2.2 (e) Analog Output Connector
    • 2.2.3 Shutter Speed Control Dial (TM-2016-8 only)
      • TABLE 5. Shutter Speed Control Dial
    • 2.2.4 RS-232 Communication Cable (TM-2016-8 only)
      • FIGURE 4. Serial Communication Cable RS-232B-12
    • 2.2.5 Digital Output Cable (TM-2016-8 only)
      • FIGURE 5. Pinout Configuration for Digital Output Cable
    • 2.2.6 Camera Link Cable (TM-2016-8CL only)
    • 2.2.7 Power Supplies and Power Cable Setup
      • 2.2.7 (a) Power Supplies
      • 2.2.7 (b) JAI, Inc. Power Cables
        • FIGURE 6. 12P-02S Interface Cable (optional)
      • 2.2.7 (c) “K” Series Power Supplies
        • 1. Attach the 110V line cord to the two terminals marked “AC.” Do not plug the cord into a 110V AC socket until you have completed steps 1 through 3.
        • 2. Attach the Gray and Yellow leads of the power cable to the Ground and 12V DC terminals, respectively.
        • 3. Replace the plastic terminal guard on the power supply.
      • 2.2.7 (d) Building Your Own Power Cable
      • 2.2.7 (e) Attaching the Power Cable to the Connector
        • 1. Rotate the connector while applying slight pressure until the keyways line up.
        • 2. Press the connector into place until firmly seated.
        • 3. Plug the power cord into the 100V AC socket. This will power the camera up.
    • 2.2.8 Attaching the Analog Video Output
    • 2.2.9 Attaching the Camera Lens
• 3 Operation
  • 3.1 Camera Rear Panel (TM-2016-8)
    • 3.1.1 Up/Down Switch
    • 3.1.2 Digital Output Connector
    • 3.1.3 Analog Output Connector
    • 3.1.4 Power, RS-232, and External Sync Connector
    • 3.1.5 Shutter Speed Control Switch
    • 3.1.6 Mode Selection Switch
      • TABLE 6. Mode Selection Switch
  • 3.2 Camera Link Rear Panel (TM-2016-8CL)
    • 3.2.1 Digital Output Connector
    • 3.2.2 Analog Output Connector
    • 3.2.3 Power and External Sync Connector
  • 3.3 Progressive Scanning
    • 1. Progressive Scanning digital and analog output
    • 2. Double-speed scanning output (two-row binning)
  • 3.4 Electronic Shutter
  • 3.5 Integration
  • 3.6 Asynchronous Reset
    • 3.6.1 External VINIT With Pulse Width
    • 3.6.2 No Delay Shutter and Read-out-inhibit (ROI)
    • 3.6.3 Internal Shutter Speed Control
  • 3.7 Dynamic Range Control
    • 3.7.1 Programmable Look-Up Table (LUT) and Knee Control
      • FIGURE 7. Look-Up Table
  • 3.8 Scan Modes
    • 3.8.1 Full Progressive Scan
    • 3.8.2 Two-Row Binning
  • 3.9 External Sync and Pixel Locking
  • 3.10 Camera Timing Charts
    • 3.10.1 Pixel Clock Locking (optional)
  • 3.11 Serial Communication Kit (TM-2016-8)
• 4 Troubleshooting
  • 4.1 Problems and Solutions
    • 4.1.1 Symptom: No Video
    • 4.1.2 Symptom: Dark Video
    • 4.1.3 Symptom: Non-synchronized Video
  • 4.2 Information and Support Resources
• 5 Appendix
  • 5.1 Specifications
    • TABLE 7. TM-2016-8 and TM-2016-8CL Product Specifications Table
  • TM-2016-8 and TM-2016-8CL
  • 1”, 7.4µm x 7.4µm progressive scan interline transfer CCD
  • 1920 (H) x 1080 (V)
  • 15.90 (H) mm x 8.61 (V) mm
  • 7.4µm x 7.4µm
  • 1920 x 1080 lines at 8Hz,
  • 1920 x 540 at 16Hz (two-row binning)
  • Internal/external auto switch
  • HD/VD, 4.0 Vp-p impedance 4.7K½
  • HD=9.09kHz±5%
  • VD=8Hz±5%, non-interlace
  • 20.000 MHz
  • Digital: 1920 (H) x 1080 (V), Analog; over 1200 TV lines (H) x 800 TV lines (V)
  • 50dB min. (AGC: off)
  • 2.0 lux f=1.4
  • Sensitivity: 13µV/ e-
  • Analog: 1.0 Vp-p composite video, 75½
  • Digital output: 8-bit RS-644 output (A/D input from CCD: 10-bit)
  • Camera Link (TM-2016-8CL only)
  • OFF
  • Programmable LUT (1.0 std.)
  • C-mount (use 1” format lenses)
  • (Adjustable back focus: optional)
  • 12V DC, 440mA (current measured at 25°)
  • -10°C to 45°C
  • 7 Grms (10Hz to 2000Hz)
  • 70G, 10-11msec
  • 44mm x 44mm 64mm (1.75” x 1.75” x 2.50”)
  • 136 grams, 4.8 oz. (141gr, 5.0 oz.: CL version)
  • RS-644 output, adjustable back-focus front end
  • 30DG-02 digital output cable,
  • CS-232E serial communication kit (TM-2016-8),
  • 26CL-02-26 Camera Link output cable (TM-2016-8CL)
  • 12P-02S
  • PD-12UU series (includes power connector)
    • 5.1.1 Physical Dimensions
      • FIGURE 8. Physical Dimensions (TM-2016-8)
      • FIGURE 9. Physical Dimensions (TM-2016-8CL)
    • 5.1.2 Spectral Response
      • FIGURE 10. Spectral Response