JVC DT-V17L2D - Manual (Page 12)

11
ENGLISH
Setting of “E.AUDIO GROUP”
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.
1G: channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)
2G: channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)
1-2G: channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)
3G: channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)
1-3G: channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/
9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)
Example of the level meter display —Level meter position and audio channels
Ex.: When “LEVEL METER ch” is set to “LINE” and “BAR TYPE” is set to “3COLORS.”
Operation guide
Shows the buttons for
each operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
AUDIO SETTING
Setting for the audio output balance, EMBEDDED AUDIO signals and level meter
Item To do Setting value
BALANCE Adjust the balance between the right and left
speakers. L5 – L1, 0, R1 – R5
E.AUDIO
GROUP*
1
Select the audio channel group of the
EMBEDDED AUDIO signals. ☞ “NOTE”
LEVEL METER
SETTING*
1
Adjust the level meter display for the
EMBEDDED AUDIO signals. ☞ “NOTE”
LEVEL
METER ch Select how the audio channels are displayed
on the level meter. OFF, LINE (Displays the channels 1 – 6 at the left
of the screen and 7 – 12 at the right.), DIVIDE
(Displays the odd channels at the left of the screen
and the even channels at the right.)
BAR TYPE Select the color of the level meter display. 3COLORS (3 colors to indicate variations in input
levels), W.100 (white)
REFERENCE
LEVEL Select the standard input level indicated on
the level meter. –20dB, –18dB
OVER LEVEL Select the input level’s lower limit indicated in
red for the “3COLORS” display. –10dB, –8dB, –6dB, –4dB, –2dB
BAR
BRIGHTNESS Select the brightness of the level meter. LOW, HIGH
SYNC FUNCTION
Setting for the synchronization with signals
Item To do Setting value
NO SYNC ACTION Select the screen status when no signal is
coming in. OFF,
P.SAVE (power save mode),
GRAY B. (gray screen)
DELAY TIME Select the period until the screen status
changes as selected in “NO SYNC ACTION”
after signals stop coming in. 30sec., 5min., 15min.
LOW LATENCY Activates/deactivates the function to shorten
the time taken to display the picture (low latency
function).
• If the picture is not displayed steadily while
“ON” is selected, select “OFF.”
• While “ON” is selected, the displayed picture
may become unstable when an operation
using buttons on the front panel or the menu
is performed, or when the signal format
changes.
ON, OFF
• Setting “NO SYNC ACTION” to “GRAY B.” saves the power consumption of the back light by half. (The screen
color changes to gray.)
Selecting “P.SAVE” saves more power consumption by turning off the back light.
* 1 Memorized for each input.
OVER LEVEL REFERENCE LEVEL
Yellow
Green
Red
Adjustment bar
Displayed when selecting
“BALANCE.”
NOTE
• When “BAR TYPE” is set to “W.100,” the standard
input level set in the “REFERENCE LEVEL” is
displayed with the line indication. The input level set in
“OVER LEVEL” is not displayed.
• The level meter with no audio signal input is displayed
in white for “3COLORS,” and in gray for “W.100.”
• You can select the position of the level meter
display—top or bottom of the screen ( ☞ “POSITION”
in “INFORMATION” on page 13).
DT-V17L2D_EA_EN_R.indd 11 DT-V17L2D_EA_EN_R.indd 11 07.9.14 7:01:47 PM 07.9.14 7:01:47 PM