JVC DR-MH50S - Manual (Page 47)

EN
47
TIMER RECORDING
You can programme this unit to timer record as many as
16 programmes.
If you do not know the
a
number for the programme you
wish to record, use the following procedure to set your unit to timer
record the programme.
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press selection keys to select ACALENDAR PR.B, then press
ENTER.
● When APROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES B appears on the TV screen, you need to
cancel some of the reserved programmes. ( A pg. 48)
4
Press selection keys to select the desired date, then press
ENTER.
5
Press selection keys
to select
ARECORD
TO B, then press
ENTER. Press
selection keys to
select the desired
recording deck, then
press ENTER.
6
Press selection keys
to select
ASTARTB,
then press ENTER.
Press selection keys to set the desired start time, then press
ENTER.
● Each press of F G increases/decreases the start time in
1 minute interval.
● To increase/decrease the start time in 30 minutes interval,
press and hold
F G.
7
Press selection keys to select ASTOPB, then press ENTER.
Press selection keys to set the desired stop time, then press
ENTER.
● Each press of F G increases/decreases the stop time in
1 minute interval.
● To increase/decrease the stop time in 30 minutes interval, press
and hold
F G.
8
Press selection keys to select ATV PROGB, then press
ENTER. Press selection keys to select the desired channel.
9
Press selection keys to select ACONFIRMB, then press
ENTER.
10
Set the other recording options as required.
● Refer to step 8 in Ac Timer ProgrammingB (A pg. 45).
11
Press selection keys
to select
AOKB, then
press ENTER to
access the
Programme
Confirmation screen.
12
Press selection keys
to select
AEXITB, then
press ENTER to
complete timer
programming.
● To programme another timer, press selection keys to select
ACONTINUEB, then press ENTER.
● If APROGRAMME OVERLAPPEDB appears on the TV
screen, delete or modify the programmes.
NOTES:
● When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.
● If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
AUX
PROGRAMME
ENTER
FGDE
CABLE/SAT
DVD TV
Selection Keys
BBC1
[MISC. ] XP
BBC1
23:00
22:30
HDD
[0]: SAT
2 PROGRAMME > CALENDAR PR. (2/3)
CONFIRM
14/01/04 WED 22:30 - 23:00
RECORD TO
STOP
START
TV PROG
ENTER
SELECT
PROGRAMME
EXIT
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
Satellite Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform ASatellite Receiver Control SettingB (A pg. 22).
B Perform AManual Timer ProgrammingB (A pg. 47).
In step 8, press AUX to change ATV PROGB to ASATB. Then
press selection keys to enter the channel position for the
satellite broadcast.
C Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
BBC1
1:00 28:00
2 PROGRAMME > CALENDAR PR. (3/3)
OK
INPUT TITLE
CATEGORY
VPS/PDC
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
OFF
MON-FRI (FOR A WEEK)
FR360
14/01/04 WED 22:30 - 23:00
GARDENING
[EDUCATION] FR360
ENTER
SELECT
PROGRAMME
EXIT
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]