Samsung SC-140 - Manual (Page 4)

6 7
Resolving Technical Problems
☛ Please consult the following table BEFORE contacting your dealer or local SAMSUNG
☛ representative.
The software installation failed ◆ Check that your hard disk is not full.
◆ The installation floppy disk may be corrupted.
Repeat the installation with the backup floppy disk.
After installing the device driver, your system
start-up program may take more time than
expected. If it does not start-up after 60 seconds,
verify your AUTOEXEC. BAT file and, if
necessary, contact your local computer dealer. I re-booted my PC and it paused
during the start-up program.
Problem Meaning / Solution
◆ When the program of Windows 95/98 is broken up, re-stall
◆ it as the computer can not read the program anymore.
◆ Verify the connections between the drive and your PC.
◆ Check that the 40-pin flat cable is connected to an IDE
◆ interface (some PCs are equipped with an SCSI disk
◆ interface).
◆ Verify your AUTOEXEC. BAT file. Go to page 5 for
◆ the verification procedure.
◆ Check the LASTDRIVE = command in the CONFIG. SYS
◆ file. The specified letter must take the CD-ROM volume
◆ into account. If you do not know which letter is assigned
◆ to the CD-ROM, enter Z.
◆ Using the documentation provided with your PC, check
◆ that the IDE hard disk is set up in MASTER mode.
I installed the software and re-
booted my PC. The CD-ROM
drive icon/directory still does not
appear.
The drive may not be installed correctly. Verify the
physical installation. The disc tray does not open.
If you have installed the
CD-ROM drive ... Then ...
And the software Re-boot your PC.
Install the software
following the instructions
on page 5.
In the File Manager, the CD-ROM
icon does not display.
And have not installed
the software
Technical Specifications
Max. 6000KB/s Max. 7200KB/s
SC-140 SC-148 SECTIONS
DISC
DRIVE PER -
FORMANCE
FRONT PANEL
REAR PANEL
OPERATING
ENVIRONMENT
GENERAL
RELIABILITY
ERROR RATE
Disc types supported
Disc diameter
Data transfer rate
Access time (1/3 stroke)
Data buffer capacity
Laser
Slide mechanism
Spindle motor
Loading type
Button
Indicator(LED)
Headphone output
Volume control
Required power
Interface connector
Audio output
Jumper block
Work area
Storage area
Dimensions
Net weight
MTBF
Disc compartment loading
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,
Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),
Video CD ready, Enhanced CD, CD-I/FMV, CD-R
12cm or 8cm
PIO Mode - 4. DMA MW2
80ms(typical) 70ms(typical)
128KB
Semiconductor Laser
Gear motor
Brushless motor
Tray Loading, DC motor(Soft Eject)
Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits
Open/Close
Busy
Stereo Mini - jack (¯ 3,6 mm) 0.60 ± 20% (Vrms) 33½
Dial type
+5V DC 1.7A,
+12V DC 1.0A
ATAPI
Line out 0.70 ± 20%(Vrms), 47k½
Device configuration jumper
Temperature : 5~45 ¡C, Humidity : 8~80%
Temperature : -40~60 ¡C, Humidity : 5~90%
950g
125,000 POH(Duty 20%)
30,000 times
149(W) x 42.5(H) x 200(D)mm
(Including bezel)
SAMSUNG continually strives to improve its products. Both the design
specifications and these user instructions are thus subject to change without
notice.
12 9