Sunbeam 3964-099 User Manual
Page 3
5
4
T
O
F
ILL THE
W
ATER
R
ESERVOIR
1. Make sure the iron is unplugged. Set the Steam Lever to
O
/Off (Dry) and the
Fabric Select Slide to OFF.
2. Lift the Water Fill Hole Cover.
3. Fill water cup with water. Pour water into iron water reservoir. Do not fill water
reservoir beyond maximum fill level.
W
ARNING
: To prevent the risk of burns, be careful when filling a hot iron with
water. Hot metal parts, hot water and steam can cause injuries.
D
RY
I
RONING
1. Make sure the Steam Lever is turned to the
O
/Off (Dry) setting.
2. Plug the cord into a 120-Volt AC outlet.
3. Select the fabric setting you desire using the Fabric Select Slide (Silk or Synthetics).
Allow the iron to heat for 2 minutes. While the iron is heating, make sure
it is sitting on its heel rest on a stable, protected surface.
N
OTE
: While the Steam Lever is turned to the
O
/Off (Dry) setting, you may still use
the SHOT OF STEAM
®
or SPRAY MIST
®
feature. Please make sure the water reservoir
is 1/4 full of water.
T
IP
: Refer to the Ironing Guide (on Page 8) for the recommended setting for your fabric.
S
TEAM
I
RONING
1. Make sure the Steam Lever is turned to the
O
/Off (Dry) setting.
(This Step is not necessary for Irons with the Drip Free™ feature)
2. Follow the instructions for “Filling the Water Reservoir”.
3. Plug the cord into a 120-Volt AC outlet.
4. Select the fabric setting you desire using the slide (Synthetic, Silk, Linen,
Cotton or Wool). Allow the iron to heat for 2 minutes. While the iron is heating,
make sure it is sitting on its heel rest on a stable, protected surface.
5. Allow the iron to heat for 2 minutes, and then turn the Steam lever to the
appropriate setting.
T
IP
: Refer to the Ironing Guide (on Page 8) for the recommended setting for your fabric.
I
MPORTANT
: When not ironing, always set the Steam Lever to
O
/Off (Dry) and the
Fabric Slide to OFF.
U
SING THE
I
RON
’
S
S
PECIAL
F
EATURES
S
PRAY
M
IST
®
F
EATURE
The SPRAY MIST
®
feature is a powerful water spray mist that dampens the fabric
to aid in removing wrinkles from heavy fabrics and for setting creases.
To use the SPRAY MIST
®
Feature:
Press the SPRAY MIST
®
button firmly.
S
HOT OF
S
TEAM
®
F
EATURE
(Select Models Only)
The SHOT OF STEAM
®
feature provides an extra burst of steam for deep penetration
of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the
water reservoir must be at least 1/4 full of water.
To use the SHOT OF STEAM
®
Feature:
Place the iron on top of the wrinkle and press the SHOT OF STEAM
®
button each
time you would like an extra burst of steam. The SHOT OF STEAM
®
feature may
be used continuously with just a short pause between shots.
V
ERTICAL
S
TEAM
(Select Models Only)
The vertical steam feature allows your iron to function as a garment steamer.
T
IP
: When using the vertical steam on clothing, hang the clothing on a clothes hanger
for best results. Hanging curtains and drapes may also be steamed.
To use Vertical Steam:
1. Make sure that the iron has heated up (2 minutes).
2. Hold the iron in a vertical position, with the iron close to but not touching
the fabric you want to steam.
3. With your other hand, pull the fabric tight.
4. Press the SHOT OF STEAM
®
button for approximately 3-second intervals
as you move the iron across the wrinkled area.
WARNING: To prevent the risk of burns, keep your hand away from the area being
steamed.
WARNING: DO NOT steam garments while wearing them; this may result
in injuries.
T
IMED
A
UTO
-O
FF
(Select Models Only)
After 30 minutes, the power indicator light will flash steadily. This indicates
that the iron is no longer heating.
To restart the iron, push button to restart. If you do NOT want to iron any
longer, unplug the iron. Then turn the small Steam dial to Dry/O and the large
Fabric/Temperature dial to Off/O.
WARNING: Auto-Off is a safety feature and is not a recommended means for
turning your iron off. See “Caring for Your Iron After Use.”
P
ATENTED
M
OTION
S
MART
®
A
UTO
-O
FF
F
EATURE
(Select Models Only)
When the iron is plugged in, the Power Indicator will light steadily, indicating that
there is power to the iron.
If you leave the iron:
• in a horizontal position without moving it, or accidentally tip the iron over,
it will automatically stop heating after 30 seconds. The Power Indicator
will blink to let you know that the iron has stopped heating.
• in a vertical position (on its heel rest) without moving it, the iron will
automatically turn off after 15 minutes. The Power Indicator will blink
to let you know that the iron has stopped heating.
I
MPORTANT
: The Power Indicator will continue to blink until the iron is unplugged
or reset.
To reset the iron:
Move the iron back and forth and allow it to reheat for 2 minutes.
The indicator will stop blinking and the iron will start heating again.