Smarthome 7307 - Manual (Page 11)

– 20 –
ADVANCED PROGRAMMING
To program sensors to send their signals to a different zone, you must first
clear them from communicating with their current zone.
TO CLEAR A ZONE
1. Enter the current MPIN.
2. Press [ B ].
3. Press the number key to identify current zone [ 1, 2, 3 or 4 ].
The zone light(s) will flash for eight seconds.
4. While the zone light(s) are flashing, press [ * ].
Now both the green and red lights flash for 30 seconds.
5. Do not activate any sensors while these lights are flashing.
Once the lights stop flashing, the zone is cleared of all devices.
Now that you have cleared the zone from communicating with all sensors, program
the sensors to the zones you would like them to communicate with, (see below).
TO PROGRAM A SENSOR TO A ZONE:
1. Enter the current MPIN.
2. Press [ B ].
3. Press the number key to identify which zone to add the sensor to, zone
[ 1, 2, 3 or 4 ].
The zone light(s) will flash for eight seconds.
4. While the zone light(s) are flashing, press [ * ].
Now both the green and red lights flash for 30 seconds.
5. While the zone lights are flashing, go to the remote sensor you are adding and
activate it. Walk in front of the motion sensor or open the door/window.
You will hear a long beep, the zone light will stop flashing and the remote
sensor will now communicate to that zone.
Note : You can only add remote devices to a zone one by one, but you can
not remove them one by one. You must clear all sensors from the zone and
add back the ones you want.
TO PROGRAM THE MOTION SENSOR TO THE SECURITY CONTROL
PANEL (SC-001):
1. Set the switch on the side of the Motion Sensor to “ON”. Wait 60 seconds
to warm up.
2. Enter the current MPIN (Master Personal Identification Number).
– 21 –
3. Press [B].
4. Press the number key to identify which zone to add the Motion Sensor to
[1, 2, 3, 4]. We recommend you program the motion sensor to zone 2. The
zone light will flash for eight seconds.
5. While the zone light is flashing, press [ * ].
6. While the zone light is flashing, walk in front of the Motion Sensor in order to
activate it. You will hear a long beep if the motion sensor is “learned” to the
control panel. The zone light will stop flashing and the remote sensor will now
communicate to that zone.
TO DELETE A KEYCHAIN TRANSMITTER FROM ZONE 5:
1. Enter the current MPIN.
2. Press [ B ].
3. Press [ 5 ].
4. Press [ * ].
5. Do not activate any Keychain Transmitters or sensors for 30 seconds after
the [ * ] was pressed.
You have now cleared zone 5 from communicating with all Keychain Transmitters.
Please re-program the keychain transmitters that you would like to use by
the following instruction.
TO PROGRAM A KEYCHAIN TRANSMITTER OR KEYPAD TRANS-
MITTER (OPTION) TO ZONE 5:
1. Enter the current MPIN.
2. Press [ B ].
3. Press [ 5 ].
4. Press [ * ].
5. Within 30 seconds of pressing the [ * ], press any of the four buttons on the `
Keychain Transmitter OR press the panic button on the Keypad Transmitter.
You will hear a long beep and the Keychain Transmitter will now communicate
with zone 5.
NOTE: Zone 5 is designated for keychain and keypad transmitter ONLY.
Please do not program any sensors other than keychain and keypad trans-
mitters into zone 5, otherwise the system will not work properly.
ADVANCED PROGRAMMING
SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #7307