SUPER MICRO Computer SUPERO X8SIA-F - Manual (Page 61)

Chapter 2: Installation
2-35
SP1
+
+
B1
JB T1
IPMB
JD1
JPW1
JPW2 JPI2C
JWOL
JWF1
JF1
FAN2
FAN1
FAN5
FAN3
FAN4
T-SGPIO1
T-SGPIO2 JI2C1
JI2C2
JWOR
JL1
3
JPUSB1
JLED
JPL1
JPL2
JPG1
LE1
C
C
LE7
J*
W83627DHG
IDT 89HI0524G2PS
PCH
Her
mon
SLOT7 PCI-E 2.0 (2.5GT/s) X1
SLOT6 PCI-E 2.0
SLOT5 PCI-E 2.0 X8
SLOT4 PCI-E 2.0 X8
SLOT3 PCI-E 2.0 (2.5GT/s) X1
USB8/9
FAN2/CPUF
AN
USB4
USB5
FAIL PWR
DOM PWR
JWOL:
I-SATA4 I-SATA3
UID
DIMM2A
DIMM2B
DIMM2C
DIMM1B
DIMM1A
Chassis I
ntrusion
Wake on Lan
Wake on Ring
CMOS CLEAR
1-2:ENABLE 2-3:DISABLE JPL2:LAN2 JPL1:LAN1
2-3:DISABLE 1-2:ENABLE
JPB:BMC
JPI2C:PWR I2C
JSPK
:Buzz
er/Speaker
COM2
FLOPPY
DDR3 1066/1333 UDIMM/RDIMM required
JL1:
LAN1/LAN2
JPUSB1:B/P USB WAKE UP 1-2:ENABLE 2-3:DISABLE
JI2C1/JI2C2
USB6/7
2-3:Disable 1-2:Enable
CPU
JLED:P
ow er LED
OFF:Disable ON:Enable
2-3:DISABLE 1-2:ENABLE
JF1 ON
LED
LED PWR
HDD
NIC1
NIC2
OH/FF
RST
PWR
I-SATA2 I-SATA1
I-SATA0
I-SATA5
SLOT2 PCI-E 2.0 (2.5GT/s) X4 (IN X8 SLOT)
SLOT1 PCI 33MHz
DIMM1C
JPG1: VGA
KB/MOUSE
VGA
COM1
IPMI_LAN
USB0/1 USB2/3
X8SIA
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note: For an ATX power supply, you must completely shut down the system, remove
the AC power cord and then short JBT1 to clear CMOS.
A
A. Clear CMOS
B. JI
2 C1
C. JI 2 C2
B
PCI Slot_SMB Enable
Jumper Settings
Jumper Setting Definition
Short Enabled
Open (Default) Disabled
PCI Slot SMB Enable
Use Jumpers I
2 C1/I 2 C2 to enable PCI
Slot SMB (System Management Bus)
support to improve system management
for the PCI slots. See the table on the
right for jumper settings.
C