Samsung SCC-C6403 - Manual (Page 19)

3-13
E
(VIDEO SET)
IRIS ALC...
SHUTTER AUTO X2...
MOTION F.FAST
WHITE BAL ATW1
DIS ---
FOCUS MODE ONEAF
SPECIAL ...
EXIT
QUIT
AGC
The AGC menu was designed to provide you with brighter screen
supposed you photographed any subject in the dark resulting in less
brighter image than regulated. AGC menu setup is available only when
the SHUTTER menu is set to Fast Shutter or Off. Press either Left and
Right to go to LOW or HIGH and the AGC function will be activated. LOW
is use to lower the maximum AGC GAIN and HIGH raise the maximum
AGC GAIN.
❈ When the COLOR/BW menu of the camera set is set to AUTO..., AGC will
be displayed as “---“. You can’t adjust the settings manually.
MOTION
The MOTION function is available only when the SHUTTER men is set to
Slow Shutter AUTO, being composed of 5 steps, S.SLOW, SLOW,
NORM, FAST, F.FAST.
● S.SLOW reduces the amount of AGC as much as possible to monitor
subjects with no immobility in the dark.
● SLOW reduces the amount of AGC to monitor subjects with little
immobility in the dark.
● NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.
● FAST raises the amount of AGC to monitor fast subjects in the dark.
● F.FAST reduces the amount of AGC as much as possible to monitor
very fast subjects in the dark.
When the SHUTTER menu is set to AUTO, press Down to locate the
cursor in the MOTION menu and press Left and Right for MOTION
function setup. Press Left to the SLOW side and Right to the FAST side.
(VIDEO SET)
IRIS ALC...
SHUTTER OFF
AGC LOW
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT
QUIT
3-12
SHUTTER
You may designate both the fast electronic shutter speed and low
electronic shutter speed in the SHUTTER menu. The fast electronic
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to
be used for the bright and fast video image. The AUTO slow electronic
shutter supports 12 shutter speeds from x2 to x160 and sets the shutter
speed to be slow In order to make the image on the screen more distinct
and brighter when you photograph under dark illumination. If you want to
sense the light brightness to control the shutter speed to the brightness
automatically, select the AUTO slow shutter.
Keep pressing both Left and Right in the SHUTTER menu, the speed will
change in the following sequence.
➝ OFF ➝ AUTO X2... ➝ AUTO X4... ➝ AUTO X6... ➝ AUTO X8... ➝ AUTO X12... ➝
AUTO X16... ➝ AUTO X24... ➝ AUTO X32... ➝ AUTO X48... ➝ AUTO X64... ➝
AUTOX96... ➝ AUTO X128... ➝ OFF ➝ 1/100(1/120) ➝ 1/250 ➝ 1/500 ➝ 1/1000 ➝
1/2000 ➝ 1/4000 ➝ 1/10K
(VIDEO SET)
IRIS ALC...
SHUTTER OFF
AGC
OFF
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT
❈ If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be displayed
as “MF“ (the product can operate only in MF mode). You can ’t adjust the settings manually.
If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product will recover the previous
FOCUS mode.
❈ If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed as
“---“ (it can only operate in Off mode). You can ’t adjust the settings manually.
If you set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.
➜
Press
[Enter]
(FLICKERLESS)
FLICKERLESS OFF
RET
(VIDEO SET)
IRIS ALC...
SHUTTER AUTOX2...
MOTION NORM
WHITE BAL ATW1
DIS ---
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT
FLICKERLESS
Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is
designed to avoid image flickering on the screen due to inconsistency between the
vertical synchronizing frequency of the picture and the flashing frequency of the
lightening. If you select and set AUTO to ON in SHUTTER from VIDEO SET, you can set
NTSC or PAL for your area and the auto shutter speed is fixed at 1/100(1/120) second.
00570A-SCC-C6403-ENG 8/17/06 1:51 PM Page 3-12