Sanyo AVM-3280G - Manual (Page 13)

13
R L
R
L
R L
S-VIDEO IN -1
AUDIO
VIDEO
INPUT
1
VIDEO
(MONO)
S-VIDEO IN -2
AUDIO
VIDEO
INPUT
2
AUDIO
(MONO)
VIDEO AUDIO
AUDIO
OUTPUT
UHF/VHF/CATV
75Ω
❶
❷
Back of TV
MODEL AVM-3680G
Stereo Amplifier
USING THE AUDIO OUTPUT JACKS
CONNECTING A STEREO AMPLIFIER TO AUDIO OUT JACKS
1. Connect the TV Audio Output (R/L)
❶
to the Stereo Amplifier In (R/L)
❷
.
2. Press POWER on remote control to turn on the TV. Turn on external equipment also.
QuickTips
■ Position your TV at
least 2 feet from
stereo speakers. The
magnets in the speak-
ers may affect the
picture quality.
■ D O NOT connect
external speakers
directly to the TV.
■ Always match cables
according to the
colors;
RED for right
audio, WHITE for left
audio and YELLOW for
video.
■ Make sure all cable
connectors are fully
seated on the jacks.
■ Make sure you select
TV channel to match
your VCR output
(Ch. 3 or 4). See
chart on page 15.
■ To view two TV
programs or watch a
TV program and pre-
recorded tape at the
same time follow
steps on page 14.
■ If you are connect-
ing your TV to a
satellite dish, you
must have two (2)
receivers or use a
cable system or
antenna with the
satellite to use the
PIP feature.
USING THE AUDIO/ VIDEO INPUT JACKS
FOR PIP
The PIP feature requires two signals to work: You must connect signals to the 75 ohm
terminal and to one set of the A/V jacks; or you must connect signals to both sets of A/V jacks.
CONNECTING A SATELLITE SYSTEM AND CABLE
1. Connect signal (cable or antenna) to the TV 75 Ω (ohm) terminal ❶ .
2. Connect Satellite S-Video Out to TV S-Video In jack.
Using the S-Video In 1 jack overrides the Video1 Input jack and the S-Video In 2 jack
overrides the Video2 In jack (Model AVM-3680G).
3. Connect the Satellite Audio Out (R/L) jacks to TV Audio Input (R/L) jacks.
Press POWER key to turn on the TV. Turn on external equipment also.
UHF/VHF/CATV
75Ω
AUDIO VIDEO
(MONO)
R
L
L R
AUDIO VIDEO
(MONO)
L R
S-VIDEO IN -1
AUDIO
VIDEO
INPUT
1
S-VIDEO IN -2
AUDIO
VIDEO
INPUT
2
AUDIO
OUTPUT
IN FROM
SAT.
CATV IN
OUT TO TV S-VIDEO
CH3
CH4
R- -L AUDIO VIDEO
R- -L AUDIO VIDEO
❸
❷
❶
Back of
Satellite
Receiver
Back of TV
(MODEL AVM-3680G)
Cable or Antenna
system
(See page 4.)
R L
R
L
R L
S-VIDEO IN -1
AUDIO
VIDEO
INPUT
1
VIDEO
(MONO)
S-VIDEO IN -2
AUDIO
VIDEO
INPUT
2
AUDIO
(MONO)
VIDEO
AUDIO
AUDIO
OUTPUT
UHF/VHF/CATV
75Ω
❶
❷
Back of TV
MODEL AVM-3680G
Stereo Amplifier
USING THE AUDIO OUTPUT JACKS
CONNECTING A STEREO AMPLIFIER TO AUDIO OUT JACKS
1. Connect the TV Audio Output (R/L)
❶
to the Stereo Amplifier In (R/L)
❷
.
2. Press POWER on remote control to turn on the TV. Turn on external equipment also.
QuickTips
■ Position your TV at
least 2 feet from
stereo speakers. The
magnets in the speak-
ers may affect the
picture quality.
■ D O NOT connect
external speakers
directly to the TV.
■ Always match cables
according to the
colors;
RED for right
audio, WHITE for left
audio and YELLOW for
video.
■ Make sure all cable
connectors are fully
seated on the jacks.
■ Make sure you select
TV channel to match
your VCR output
(Ch. 3 or 4). See
chart on page 15.
■ To view two TV
programs or watch a
TV
d
USING THE AUDIO/ VIDEO INPUT JACKS
FOR PIP
The PIP feature requires two signals to work: You must connect signals to the 75 ohm
terminal and to one set of the A/V jacks; or you must connect signals to both sets of A/V jacks.
CONNECTING A SATELLITE SYSTEM AND CABLE
1. Connect signal (cable or antenna) to the TV 75 Ω (ohm) terminal ❶ .
2. Connect Satellite S-Video Out to TV S-Video In jack.
Using the S-Video In 1 jack overrides the Video1 Input jack and the S-Video In 2 jack
overrides the Video2 In jack (Model AVM-3680G).
3. Connect the Satellite Audio Out (R/L) jacks to TV Audio Input (R/L) jacks.
Press POWER key to turn on the TV Turn on external equipment also