Sharp Insight Electric Rang - Manual (Page 3)


InstallatIon Manual
To reduce the risk of tipping the range, it must
be secured by properly installed Anti-Tip bracket packed with
the range.
• This range must be electrically grounded in accordance with
local codes, or in their absence, with the National Electrical
Code ANSI/NFPA No. 70—latest edition in United States.
• The installation of ranges designed for manufactured (mobile)
home installation must conform with Manufactured Home
Construction and Safety Standard, title 24CFR, part 3280
[Formerly the Federal Standard for Mobile Home Construction
and Safety, title 24, HUD (part 280)] or when such standard
is not applicable, the Standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities
and Setups), ANSI Z225. 1/NFPA 501A- latest edition, or with
local codes in United States.
• Make sure the wall coverings and the cabinets around the range
can withstand the heat generated by the range.
• Before installing the range in an area covered with
linoleum or any other synthetic floor covering, make sure
the floor covering can withstand heat at least 90˚F (32.2˚C)
above room temperature without shrinking, warping or
discoloring. Do not install the range over carpeting unless
you place an insulating pad or sheet of 1 / 4 -inch (0.64cm) thick
plywood between the range and carpeting.
Never leave children alone or unattended in the
area where an a range is in use. As children grow, teach them the
proper, safe use of all appliances.
Stepping, leaning or sitting on the door or drawer
of this range can result in serious injuries and can also cause damage
to the range.
• Do not store items of interest to children in the cabinets
above the range. Children could be seriously burned climbing
on the range to reach items.
• To eliminate the need to reach over the cooktop, cabinet storage
space above the cooktop should be avoided.
• Do not use the oven as a storage space. This creates a
potentially hazardous situation.
• Never use the range for warming or heating the room.
• Do not store or use gasoline or other flammable vapors and
liquids near this or any other range. Explosions or fires could
result.
• Reset all controls to the “off” position after using a
programmable timing operation.
When usIng the selF-Clean Feature:
• Remove broiler pan, oven racks, food and other utensils
before self-cleaning the oven. Wipe up excess spillage. Follow
the precleaning instructions in the Operation Manual.
IMPoRtant notEs to thE InstallER
• Read all of the Installation Manual before installing the range.
• Remove all packing material from the oven and drawer before
connecting the electrical supply to the range.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
IMPoRtant notEs to thE ConsuMER
Keep this manual with your Operation Manual for future reference.
• As when using any range generating heat, there are certain
safety precautions you should follow. These are listed in the
Operation Manual. Read all and follow carefully.
• Be sure your range is installed and grounded properly by a
qualified installer or service technician.
unPaCkInG anD ExaMInInG YouR RanGE
 Remove all packing
materials from inside
the Microwave Drawer
and the oven cavity.
DO NOT REMOVE
THE WAVEGUIDE
COVER, which is
located on the top
of the Microwave
Drawer.
 Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent
drawer, damaged drawer seals and sealing surfaces, broken
or loose drawer guides and dents inside the drawer or on the
front side of the drawer. If there is any damage, do not operate
the Microwave Drawer and contact your dealer or a SHARP
AUTHORIZED SERVICER.
IMPoRtant saFEtY InstRuCtIons
If the information in this manual is not followed
exactly, a fire or electrical shock may result causing property damage,
personal injury or death.
• all ranges Can tIp
• Injury to persons Could result
• Install antI-tIp braCket paCked
WIth range
• see antI-tIp braCket teMplate
For InstallatIon InstruCtIons
Sealing Surface
Waveguide
Cover
Sealing Surface
Microwave
Drawer Cavity