Sony SRX-S105 - Manual (Page 52)

52
Location and Function of Controls
Ch
apt
er 1 Ov
e
rv
ie
w
d MUTING ON/OFF buttons
Clicking the ON button cuts off the whole picture on the
screen momentarily. Click the OFF button to restore the
picture. Activating the muting function blocks off lamp
light completely by use of a shutter, and displays the black
signal on the whole screen.
e OSD ON/OFF buttons
Click the OFF button to eliminate the on-screen display.
Click the ON button to display it on the screen.
The setting using the buttons also functions when you
operate the projector with the Remote Commander.
Remote Commander
a ?/1 (power on/standby) buttons
?: Press to turn on the projector.
1: Press to make the projector enter standby mode.
b SCREEN MODE button
Selects single-, dual- or quad-screen. Each press of the
button changes the mode, 1 (single), 2 (dual) and 4 (quad),
in this order.
c MUTING button
Press to cut off the whole picture on the screen. Press it
again to restore the picture. Activating the muting function
shuts off from lamp light completely using a shutter, and
displays the black signal on the whole screen.
d FUNCTION 1/2/3 buttons
Use these buttons in synchronization with the FUNCTION
1, 2 and 3 buttons in the Control Function Menu window
of the SRX Controller. You can recall the data set or
adjusted with the SRX Controller. You cannot recall
settings registered in FUNCTION buttons 4 to 7.
e INPUT SEL A/B/C/D buttons
Select the input source you want to project or operate.
A: Selects the signal input from the DVI-D connectors on
INPUT A.
B: Selects the signal input from the connectors on the
optional input board installed in the INPUT B section.
C: Selects the signal input from the connectors on the
optional input board installed in the INPUT C section.
D: Selects the signal input from the connectors on the
optional input board installed in the INPUT D section.
Use these buttons together with the PICTURE CONT
buttons (6) or SCREEN SEL buttons (7).
Example: When you want to increase the contrast of the
signal input from INPUT A, press INPUT SEL A
button, then press the CONTR + button.
f PICTURE CONT (Picture control) buttons
Adjust the projected picture quality.
CONTR+/–: Adjust the contrast. Pressing the + button
increases the contrast. Pressing the – button decreases
the contrast.
BRIGHT +/–: Adjust the picture brightness. Pressing the
+ button makes the picture brighter. Pressing the –
button makes the picture darker.
SHARP +/–: Adjust the picture sharpness. Pressing the +
button makes the picture sharper. Pressing the –
button makes the picture softer.
In multiple screen mode, adjustment can be made for the
input signal from INPUT A or each input board.
Select the input signal with the INPUT SEL A/B/C/D
buttons (5), then adjust the picture with these buttons. In
single-screen mode, you need not press the INPUT SEL
button.
Example: When you want to increase the contrast for the
signal input from INPUT A, press the INPUT SEL A
button, then press the CONTR + button.
g SCREEN SEL buttons
In multiple screen mode, select one of the divided screens
where you want to project the selected signal from each
input.
Select the input signal with one of the INPUT SEL A/B/C/
D buttons (5), then select the screen with one of these
buttons.
SR Projector
RM-PJ4K IR
I 1 SCREEN
MODE
1 2 4
MUTING
FUNCTION
INPUT SEL
A
1
1 2 3
2
3 4
B C D
PICTURE CONT
BRIGHT CONTR
+
–
+
–
+
–
+
–
+
–
+
–
SHARP
ZOOM FOCUS SHIFT
SCREEN SEL
LENS CONT
1
2
3
4
5
7
6
8