Star Micronics 150 - Manual (Page 91)

Programmer's Guide PcOS Series 150 Control Codes
Summary by Code
12/14/99 Rev G Page 81
Control Codes Summary by Code
Normal
ASCII Second
ASCII
field Hex Code IPCL equivalent
code Description Page
[NUL] 00 Null
[ENQ] <n> 05H Set inquire status.
(Refer to command descriptions.) 62
[BS] 08H &%BS Set back space. 16
[HT] 09H &%HT Set horizontal tabs. 16
[LF] 0AH &%LF Set line feed. 15
[VT] 0BH &%VT Set vertical tabs. 20
[FF] 0CH &%FF Set form feed. 20
[CR] 0DH &%CR Set carriage return. 15
[SO] 0EH &%MW Se one-line double-wide print. 33
[SI] 0FH &%F1 Set 17 cpi. 31
[DC2] 12H &%F3 Set 10 cpi. 31
[DC4] 14H &%MN Cancel one-line double-wide print. 33
[CAN] 18H &%RP Clear print buffer. 55
[ESC] [SI] 1BH,0FH &%F4 Set 24 cpi. 31
[ESC] [DC1] 1BH,11H &%VO Open for validation. 52
[ESC] [DC3] 1BH,13H &%VC Close for validation. 52
[ESC] [DC4] 1BH,14H &%VS Select validation mode with
autoform sense. 52
[ESC] [EM] B
<n> 1BH,19H,
42H &%BH <m
1
> Set bar code height.
n=0 Restore defaults
n=1-9 Number of passes
(0.11” per pass) 50
[ESC] [EM] C
<n> 1BH,19H,
43H &%ZC <m
1
><m
2
> Set validation clamp delay. 53
[ESC] [EM] J
<n> 1BH,19H,
4AH &%BJ <m
1
><m
2
> Set bar code justification. 50
[ESC] [EM] V
<n> 1BH,19H,
56H &%ZV<m
1
><m
2
> Set validation time-out. 53
[ESC] # <0> 1BH,23H,
30H &%QT Begin HSD mode. 22
[ESC] $ 1BH,24H Copy ROM character set to RAM
character set. 28
[ESC] % G 1BH,25H,
47H &%MI Begin italics. 38
[ESC] % H 1BH,25H,
48H &%CI End italics. 38
[ESC] *
<m><n>
1 <n>2
1BH,2AH Print graphics in mode <m>. 46
[ESC] ! <n> 1BH,21H &%CS<n> Select the International Character
Set. 24
[ESC] - <n> 1BH,2DH &%CU {n=0}
&%MU {n=1} Set underline.
n=0 end
n=1 begin 36
[ESC] 0 1BH,30H &%ST Set 1/8-inch line space. 18
[ESC] 1 1BH,31H &%SG Set 7/72-inch line space. 19
[ESC] 2 1BH,32H Begin variable line spacing.
(This enables [ESC] A <n>). 19
[ESC] 3 <n> 1BH,33H &%SV <m
1
><m
2
>
<m
3
>
Set variable space n/216-inch.
Where n=1..255 defines the feed
used by line feed. 18