Technical specifications – Samsung SW-232 User Manual

Page 9

Advertising
background image

16

Technical Specifications

17

ENGLISH

SAMSUNG continually strives to improve its products. Both the design specifications
and these user instructions are thus subject to change without notice.

DISC

GENERAL

RELIABILITY

DRIVE
PERFORMANCE

FRONT PANEL

REAR PANEL

OPERATING
ENVIRONMENT

Disc types supported
in write mode
Erasing disc types
Disc diameter

Disc types supported
in read mode

Data transfer rate

Access time (typical)

Recording

Reading

CD-R : 600 KB/sec. (4X), 1,200 KB/sec. (8X),

1800 KB/sec. (12X), 2,400 KB/sec. (16X),
3600 KB/sec. (24X), 4,800 KB/sec. (32X),

CD-R W : 1500 KB/sec. (10X), 600 KB/sec. (4X),

CD: CAV 40 Access Time CD-RW : CAV 32 Access Time
PIO Mode 4:16.6MB/sec,
Multiword DMA mode 2:16.6MB/sec

110ms (typical)

Data Buffer

8MB

Laser

Semiconductor laser

Slide mechanism

Stepping motor

Spindle motor

Brushless motor

Load mechanism

ERROR RATE

Eject button
Indicator
Headphone output
Volume control
Required power
Interface connector
Audio output
Jumper block

Tray. DC motor (Soft Eject).
Mode 1: 1 block/10

12

, Mode 2: 1 block/10

9

Auto eject or Auto inject
Play / Read (GREEN) Record (RED), Operation LED
Stereo mini-jack (Ø 3.6 mm) 0.65±20% (vrms) 33Ω
Dial type
+5 VDC: 1.5 A (max.), +12 VDC: 1.5 A (max.)
ATAPI (E-IDE)
Line out 0.75±20% (vrms) : 47KΩ
Device configuration jumper

Operations

Temperature: 5~45°C Humidity: 10~80%

Storage

Temperature: -25~55°C Humidity: 10~90%

Dimensions
Net weight
MTBF

CD-DA, CD-ROM mode 1, CD-ROM XA mode 2, Form 1,
Form 2, CD-Plus, CD-Extra, Photo-CD (Single, Multi-session),
Video CD ready, Enhanced CD, CD-I/Fmv, CD-R, CD-RW,
CD-TEXT

CD-R, CD-RW

CD-RW
120 mm or 80 mm

148.2 (W) x 42 (H) x 184 (D) mm (including bezel)
765 g
125,000 POH(Duty 20%)

ITEM

SW-232

Problem

When the MPEG software
plays a Video CD, the
pictures are not regular and
the running speed is too slow.

Adjust the size of the replay screen.

The Disc is not in message is
displayed even though a disc
has been inserted.

The computer may not recognize the disc if you

start playback too quickly after inserting the disc.

Open and close the disc compartment and try again.

The CD-R/RW drive is not
detected after it is connected
to a sound card.

The interface mode of the sound card is AT-BUS.

You must therefore connect the CD-R/RW drive to

the IDE port on the PC mother board, rather than

to the sound card, or install an E-IDE compatible

sound card.

Clean the disc and try again.

After checking the display resolution, adjust it,

if necessary.

Meaning / Solution

IN CD has the Formatted
Disc Eject function.

Right-click the mouse on TRAY ICON (right side of

the menu bar at the bottom of the monitor) and then

select "Eject" to take the CD out.

Select the drive where the disc is inserted from

Windows Explorer.

Right-click the mouse and select "Eject" to take

the CD out.

When recording NERO,
it will be recorded not on a
CD but a form of image file.

This seems to occur when you select the recording

function as the system selects "Image Recorder"

instead of SW-232.

In this case, select a recorder from the menu items

at the upper part of NERO and then select SW-232

from the Recorder Selection window.

The Recorder cannot
recognize the disc.

Use the firmware automatic upgrade function

available at the ODD service website to download

the newest firmware and then reinstall the recording

software which is included in the bundle.

- www.samsungodd.com

- www.samsungelectronics.com

When installing the recording software, try not to

install the software before the ROM drive as this

makes the Image Recorder selected.

Advertising
This manual is related to the following products: